lkml.org 
[lkml]   [2019]   [Feb]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 4/4] staging: iio: ad7780: moving ad7780 out of staging
On Thu, 14 Feb 2019 18:48:15 -0200
Renato Lui Geh <renatogeh@gmail.com> wrote:

> On 02/09, Jonathan Cameron wrote:
> >On Tue, 5 Feb 2019 15:14:03 -0200
> >Renato Lui Geh <renatogeh@gmail.com> wrote:
> >
> >> Move ad7780 ADC driver out of staging and into the mainline.
> >>
> >> The ad7780 is a sigma-delta analog to digital converter. This driver provides
> >> reading voltage values and status bits from both the ad778x and ad717x series.
> >> Its interface also allows writing on the FILTER and GAIN GPIO pins on the
> >> ad778x.
> >>
> >> Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
> >> Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
> >> Co-developed-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
> >
> >This needs a device tree binding doc which should be reviewed before we move
> >the driver out of staging. Make sure to cc the dt-binding maintainers and
> >list. Doesn't really matter if that patch is before or after this one
> >in the series but needs to be in the same series.
>
> Ok! I see that some Analog dt-bindings are prefixed by adi and some are
> not. Should I follow any naming standard?

Yeah, comes of history and the fact that we can't 'fix' a binding that
is in the wild if the driver is already out of staging. Even in the
staging case we won't generally do it if we know of real devices out
there using the defacto binding.

They should be prefixed if they aren't 'generic'. Exactly where that lines
tends to be a little unclear unfortunately.

> >
> >There are a few more minor tidy ups that would be nice to have inline
> >given you are doing a v4. Stuff like this could have been cleaned up
> >after moving out of staging (nothing wrong with improving non staging
> >drivers after all) but always better to do it whilst we remember!
> >
> >> ---
> >> Changes in v3:
> >> - Changes unrelated to moving the driver to main tree were resent as
> >> individual patches
> >>
> >> drivers/iio/adc/Kconfig | 13 ++
> >> drivers/iio/adc/Makefile | 1 +
> >> drivers/iio/adc/ad7780.c | 359 +++++++++++++++++++++++++++++++
> >> drivers/staging/iio/adc/Kconfig | 13 --
> >> drivers/staging/iio/adc/Makefile | 1 -
> >> drivers/staging/iio/adc/ad7780.c | 359 -------------------------------
> >> 6 files changed, 373 insertions(+), 373 deletions(-)
> >> create mode 100644 drivers/iio/adc/ad7780.c
> >> delete mode 100644 drivers/staging/iio/adc/ad7780.c
> >>
> >> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> >> index f3cc7a31bce5..2cdee166d0e9 100644
> >> --- a/drivers/iio/adc/Kconfig
> >> +++ b/drivers/iio/adc/Kconfig
> >> @@ -108,6 +108,19 @@ config AD7766
> >> To compile this driver as a module, choose M here: the module will be
> >> called ad7766.
> >>
> >> +config AD7780
> >> + tristate "Analog Devices AD7780 and similar ADCs driver"
> >> + depends on SPI
> >> + depends on GPIOLIB || COMPILE_TEST
> >> + select AD_SIGMA_DELTA
> >> + help
> >> + Say yes here to build support for Analog Devices AD7170, AD7171,
> >> + AD7780 and AD7781 SPI analog to digital converters (ADC).
> >> + If unsure, say N (but it's safe to say "Y").
> >
> >I wouldn't bother with this statement, doesn't add any real info!
> >
> >> +
> >> + To compile this driver as a module, choose M here: the
> >> + module will be called ad7780.
> >> +
> >> config AD7791
> >> tristate "Analog Devices AD7791 ADC driver"
> >> depends on SPI
> >> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> >> index ea5031348052..b48852157115 100644
> >> --- a/drivers/iio/adc/Makefile
> >> +++ b/drivers/iio/adc/Makefile
> >> @@ -15,6 +15,7 @@ obj-$(CONFIG_AD7606_IFACE_PARALLEL) += ad7606_par.o
> >> obj-$(CONFIG_AD7606_IFACE_SPI) += ad7606_spi.o
> >> obj-$(CONFIG_AD7606) += ad7606.o
> >> obj-$(CONFIG_AD7766) += ad7766.o
> >> +obj-$(CONFIG_AD7780) += ad7780.o
> >> obj-$(CONFIG_AD7791) += ad7791.o
> >> obj-$(CONFIG_AD7793) += ad7793.o
> >> obj-$(CONFIG_AD7887) += ad7887.o
> >> diff --git a/drivers/iio/adc/ad7780.c b/drivers/iio/adc/ad7780.c
> >> new file mode 100644
> >> index 000000000000..163e3c983598
> >> --- /dev/null
> >> +++ b/drivers/iio/adc/ad7780.c
> >> @@ -0,0 +1,359 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * AD7170/AD7171 and AD7780/AD7781 SPI ADC driver
> >> + *
> >> + * Copyright 2011 Analog Devices Inc.
> >
> >I think you have done more than enough to this driver to add
> >an additional copyright line if you want to!
>
> Oh wow, that'd be awesome! Thanks! Should I just add my full name there?

Yes.

> >
> >> + */
> >> +
> >> +#include <linux/interrupt.h>
> >> +#include <linux/device.h>
> >> +#include <linux/kernel.h>
> >> +#include <linux/slab.h>
> >> +#include <linux/sysfs.h>
> >> +#include <linux/spi/spi.h>
> >> +#include <linux/regulator/consumer.h>
> >> +#include <linux/err.h>
> >> +#include <linux/sched.h>
> >> +#include <linux/gpio/consumer.h>
> >> +#include <linux/module.h>
> >> +
> >> +#include <linux/iio/iio.h>
> >> +#include <linux/iio/sysfs.h>
> >> +#include <linux/iio/adc/ad_sigma_delta.h>
> >> +
> >> +#define AD7780_RDY BIT(7)
> >> +#define AD7780_FILTER BIT(6)
> >> +#define AD7780_ERR BIT(5)
> >> +#define AD7780_ID1 BIT(4)
> >> +#define AD7780_ID0 BIT(3)
> >> +#define AD7780_GAIN BIT(2)
> >> +#define AD7780_PAT1 BIT(1)
> >> +#define AD7780_PAT0 BIT(0)
> >These two bits of pattern don't really add anything. I'd drop them in
> >favour of something like
> >
> >#define AD7780_PATTERN_GOOD 1
> >#define AD7780_PATTERN_MASK GENMASK(1, 0)
> >
> >Same for ID for that matter. These aren't one bit fields, so we shouldn't
> >ever present them as such (though the datasheet confusingly sort of does
> >so!)
> >
> >> +
> >> +#define AD7780_PATTERN (AD7780_PAT0)
> >> +#define AD7780_PATTERN_MASK (AD7780_PAT0 | AD7780_PAT1)
> >> +
> >> +#define AD7170_PAT2 BIT(2)
> >> +
> >> +#define AD7170_PATTERN (AD7780_PAT0 | AD7170_PAT2)
> >> +#define AD7170_PATTERN_MASK (AD7780_PAT0 | AD7780_PAT1 | AD7170_PAT2)
> >I'd use a value for the pattern directly and
> >GENMASK for the mask.
> >
> >> +
> >> +#define AD7780_GAIN_GPIO 0
> >> +#define AD7780_FILTER_GPIO 1
> >> +
> >> +#define AD7780_GAIN_MIDPOINT 64
> >> +#define AD7780_FILTER_MIDPOINT 13350
> >> +
> >> +static const unsigned int ad778x_gain[2] = { 1, 128 };
> >> +static const unsigned int ad778x_odr_avail[2] = { 10000, 16700 };
> >> +
> >> +struct ad7780_chip_info {
> >> + struct iio_chan_spec channel;
> >> + unsigned int pattern_mask;
> >> + unsigned int pattern;
> >> + bool is_ad778x;
> >> +};
> >> +
> >> +struct ad7780_state {
> >> + const struct ad7780_chip_info *chip_info;
> >> + struct regulator *reg;
> >> + struct gpio_desc *powerdown_gpio;
> >> + struct gpio_desc *gain_gpio;
> >> + struct gpio_desc *filter_gpio;
> >> + unsigned int gain;
> >> + unsigned int odr;
> >> + unsigned int int_vref_mv;
> >> +
> >> + struct ad_sigma_delta sd;
> >> +};
> >> +
> >> +enum ad7780_supported_device_ids {
> >> + ID_AD7170,
> >> + ID_AD7171,
> >> + ID_AD7780,
> >> + ID_AD7781,
> >> +};
> >> +
> >> +static struct ad7780_state *ad_sigma_delta_to_ad7780(struct ad_sigma_delta *sd)
> >> +{
> >> + return container_of(sd, struct ad7780_state, sd);
> >> +}
> >> +
> >> +static int ad7780_set_mode(struct ad_sigma_delta *sigma_delta,
> >> + enum ad_sigma_delta_mode mode)
> >> +{
> >> + struct ad7780_state *st = ad_sigma_delta_to_ad7780(sigma_delta);
> >> + unsigned int val;
> >> +
> >> + switch (mode) {
> >> + case AD_SD_MODE_SINGLE:
> >> + case AD_SD_MODE_CONTINUOUS:
> >> + val = 1;
> >> + break;
> >> + default:
> >> + val = 0;
> >> + break;
> >> + }
> >> +
> >> + gpiod_set_value(st->powerdown_gpio, val);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int ad7780_read_raw(struct iio_dev *indio_dev,
> >> + struct iio_chan_spec const *chan,
> >> + int *val,
> >> + int *val2,
> >> + long m)
> >> +{
> >> + struct ad7780_state *st = iio_priv(indio_dev);
> >> + int voltage_uv;
> >> +
> >> + switch (m) {
> >> + case IIO_CHAN_INFO_RAW:
> >> + return ad_sigma_delta_single_conversion(indio_dev, chan, val);
> >> + case IIO_CHAN_INFO_SCALE:
> >> + voltage_uv = regulator_get_voltage(st->reg);
> >> + if (voltage_uv < 0)
> >> + return voltage_uv;
> >> + voltage_uv /= 1000;
> >> + *val = voltage_uv * st->gain;
> >> + *val2 = chan->scan_type.realbits - 1;
> >> + st->int_vref_mv = voltage_uv;
> >> + return IIO_VAL_FRACTIONAL_LOG2;
> >> + case IIO_CHAN_INFO_OFFSET:
> >> + *val = -(1 << (chan->scan_type.realbits - 1));
> >> + return IIO_VAL_INT;
> >> + case IIO_CHAN_INFO_SAMP_FREQ:
> >> + *val = st->odr;
> >> + return IIO_VAL_INT;
> >> + }
> >> +
> >> + return -EINVAL;
> >> +}
> >> +
> >> +static int ad7780_write_raw(struct iio_dev *indio_dev,
> >> + struct iio_chan_spec const *chan,
> >> + int val,
> >> + int val2,
> >> + long m)
> >> +{
> >> + struct ad7780_state *st = iio_priv(indio_dev);
> >> + const struct ad7780_chip_info *chip_info = st->chip_info;
> >> + unsigned long long vref;
> >> + unsigned int full_scale, gain;
> >> +
> >> + if (!chip_info->is_ad778x)
> >> + return 0;
> >> +
> >> + switch (m) {
> >> + case IIO_CHAN_INFO_SCALE:
> >> + if (val != 0)
> >> + return -EINVAL;
> >> +
> >> + vref = st->int_vref_mv * 1000000LL;
> >> + full_scale = 1 << (chip_info->channel.scan_type.realbits - 1);
> >> + gain = DIV_ROUND_CLOSEST(vref, full_scale);
> >> + gain = DIV_ROUND_CLOSEST(gain, val2);
> >> + st->gain = gain;
> >> + if (gain < AD7780_GAIN_MIDPOINT)
> >> + gain = 0;
> >> + else
> >> + gain = 1;
> >> + gpiod_set_value(st->gain_gpio, gain);
> >> + break;
> >> + case IIO_CHAN_INFO_SAMP_FREQ:
> >> + if (1000*val + val2/1000 < AD7780_FILTER_MIDPOINT)
> >> + val = 0;
> >> + else
> >> + val = 1;
> >> + st->odr = ad778x_odr_avail[val];
> >> + gpiod_set_value(st->filter_gpio, val);
> >> + break;
> >We'll get a warning here due to the lack of a default handler.
> >It's pointless except to suppress the warning, but best to add one.
> >
> >> + }
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int ad7780_postprocess_sample(struct ad_sigma_delta *sigma_delta,
> >> + unsigned int raw_sample)
> >> +{
> >> + struct ad7780_state *st = ad_sigma_delta_to_ad7780(sigma_delta);
> >> + const struct ad7780_chip_info *chip_info = st->chip_info;
> >> +
> >> + if ((raw_sample & AD7780_ERR) ||
> >> + ((raw_sample & chip_info->pattern_mask) != chip_info->pattern))
> >> + return -EIO;
> >> +
> >> + if (chip_info->is_ad778x) {
> >> + st->gain = ad778x_gain[raw_sample & AD7780_GAIN];
> >> + st->odr = ad778x_odr_avail[raw_sample & AD7780_FILTER];
> >> + }
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static const struct ad_sigma_delta_info ad7780_sigma_delta_info = {
> >> + .set_mode = ad7780_set_mode,
> >> + .postprocess_sample = ad7780_postprocess_sample,
> >> + .has_registers = false,
> >> +};
> >> +
> >> +#define AD7780_CHANNEL(bits, wordsize) \
> >> + AD_SD_CHANNEL_NO_SAMP_FREQ(1, 0, 0, bits, 32, wordsize - bits)
> >> +
> >> +static const struct ad7780_chip_info ad7780_chip_info_tbl[] = {
> >> + [ID_AD7170] = {
> >> + .channel = AD7780_CHANNEL(12, 24),
> >> + .pattern = AD7170_PATTERN,
> >> + .pattern_mask = AD7170_PATTERN_MASK,
> >> + .is_ad778x = false,
> >> + },
> >> + [ID_AD7171] = {
> >> + .channel = AD7780_CHANNEL(16, 24),
> >> + .pattern = AD7170_PATTERN,
> >> + .pattern_mask = AD7170_PATTERN_MASK,
> >> + .is_ad778x = false,
> >> + },
> >> + [ID_AD7780] = {
> >> + .channel = AD7780_CHANNEL(24, 32),
> >> + .pattern = AD7780_PATTERN,
> >> + .pattern_mask = AD7780_PATTERN_MASK,
> >> + .is_ad778x = true,
> >> + },
> >> + [ID_AD7781] = {
> >> + .channel = AD7780_CHANNEL(20, 32),
> >> + .pattern = AD7780_PATTERN,
> >> + .pattern_mask = AD7780_PATTERN_MASK,
> >> + .is_ad778x = true,
> >> + },
> >> +};
> >> +
> >> +static const struct iio_info ad7780_info = {
> >> + .read_raw = ad7780_read_raw,
> >> + .write_raw = ad7780_write_raw,
> >> +};
> >> +
> >> +static int ad7780_probe(struct spi_device *spi)
> >> +{
> >> + struct ad7780_state *st;
> >> + struct iio_dev *indio_dev;
> >> + int ret;
> >> +
> >> + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
> >> + if (!indio_dev)
> >> + return -ENOMEM;
> >> +
> >> + st = iio_priv(indio_dev);
> >> + st->gain = 1;
> >> +
> >> + ad_sd_init(&st->sd, indio_dev, spi, &ad7780_sigma_delta_info);
> >> +
> >> + st->chip_info =
> >> + &ad7780_chip_info_tbl[spi_get_device_id(spi)->driver_data];
> >> +
> >> + spi_set_drvdata(spi, indio_dev);
> >> +
> >> + indio_dev->dev.parent = &spi->dev;
> >> + indio_dev->name = spi_get_device_id(spi)->name;
> >> + indio_dev->modes = INDIO_DIRECT_MODE;
> >> + indio_dev->channels = &st->chip_info->channel;
> >> + indio_dev->num_channels = 1;
> >> + indio_dev->info = &ad7780_info;
> >> +
> >> + st->powerdown_gpio = devm_gpiod_get_optional(&spi->dev,
> >> + "powerdown",
> >> + GPIOD_OUT_LOW);
> >> + if (IS_ERR(st->powerdown_gpio)) {
> >> + ret = PTR_ERR(st->powerdown_gpio);
> >> + dev_err(&spi->dev, "Failed to request powerdown GPIO: %d\n",
> >> + ret);
> >> + return ret;
> >> + }
> >> +
> >> + if (st->chip_info->is_ad778x) {
> >> + st->gain_gpio = devm_gpiod_get_optional(&spi->dev,
> >> + "gain",
> >> + GPIOD_OUT_HIGH);
> >> + if (IS_ERR(st->gain_gpio)) {
> >> + ret = PTR_ERR(st->gain_gpio);
> >> + dev_err(&spi->dev, "Failed to request gain GPIO: %d\n",
> >> + ret);
> >> + return ret;
> >> + }
> >> +
> >> + st->filter_gpio = devm_gpiod_get_optional(&spi->dev,
> >> + "filter",
> >> + GPIOD_OUT_HIGH);
> >> + if (IS_ERR(st->filter_gpio)) {
> >> + ret = PTR_ERR(st->filter_gpio);
> >> + dev_err(&spi->dev,
> >> + "Failed to request filter GPIO: %d\n",
> >> + ret);
> >> + return ret;
> >> + }
> >> + }
> >> +
> >> + st->reg = devm_regulator_get(&spi->dev, "avdd");
> >> + if (IS_ERR(st->reg))
> >> + return PTR_ERR(st->reg);
> >> +
> >> + ret = regulator_enable(st->reg);
> >> + if (ret) {
> >> + dev_err(&spi->dev, "Failed to enable specified AVdd supply\n");
> >> + return ret;
> >> + }
> >> +
> >> + ret = ad_sd_setup_buffer_and_trigger(indio_dev);
> >> + if (ret)
> >> + goto error_disable_reg;
> >> +
> >> + ret = iio_device_register(indio_dev);
> >> + if (ret)
> >> + goto error_cleanup_buffer_and_trigger;
> >> +
> >> + return 0;
> >> +
> >> +error_cleanup_buffer_and_trigger:
> >> + ad_sd_cleanup_buffer_and_trigger(indio_dev);
> >> +error_disable_reg:
> >> + regulator_disable(st->reg);
> >> +
> >> + return ret;
> >> +}
> >> +
> >> +static int ad7780_remove(struct spi_device *spi)
> >> +{
> >> + struct iio_dev *indio_dev = spi_get_drvdata(spi);
> >> + struct ad7780_state *st = iio_priv(indio_dev);
> >> +
> >> + iio_device_unregister(indio_dev);
> >> + ad_sd_cleanup_buffer_and_trigger(indio_dev);
> >> +
> >> + regulator_disable(st->reg);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static const struct spi_device_id ad7780_id[] = {
> >> + {"ad7170", ID_AD7170},
> >> + {"ad7171", ID_AD7171},
> >> + {"ad7780", ID_AD7780},
> >> + {"ad7781", ID_AD7781},
> >> + {}
> >> +};
> >> +MODULE_DEVICE_TABLE(spi, ad7780_id);
> >> +
> >> +static struct spi_driver ad7780_driver = {
> >> + .driver = {
> >> + .name = "ad7780",
> >> + },
> >> + .probe = ad7780_probe,
> >> + .remove = ad7780_remove,
> >> + .id_table = ad7780_id,
> >> +};
> >> +module_spi_driver(ad7780_driver);
> >> +
> >> +MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>");
> >> +MODULE_DESCRIPTION("Analog Devices AD7780 and similar ADCs");
> >> +MODULE_LICENSE("GPL v2");


\
 
 \ /
  Last update: 2019-02-18 15:50    [W:0.062 / U:8.928 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site