lkml.org 
[lkml]   [2019]   [Feb]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [RFC 5/5] arm64: dts: imx8mq: Add the opp table and the cpu-supply nodes
Date
On 19-02-14 16:50:28, Lucas Stach wrote:
> Hi Abel
>
> Am Mittwoch, den 13.02.2019, 19:05 +0000 schrieb Abel Vesa:
> > Add the opp table containing only non over drive opps.
> > Also add the cpu-supply nodes for the A53 cores in the EVK board.
> >
> > Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 17 +++++++++++++++++
> >  arch/arm64/boot/dts/freescale/imx8mq.dtsi    | 23 +++++++++++++++++++++++
> >  2 files changed, 40 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > index 54737bf..114359e 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > @@ -31,6 +31,23 @@
> >   gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> >   enable-active-high;
> >   };
> > +
> > +};
> > +
> > +&A53_0 {
> > + cpu-supply = <&sw1a_reg>;
> > +};
> > +
> > +&A53_1 {
> > + cpu-supply = <&sw1a_reg>;
> > +};
> > +
> > +&A53_2 {
> > + cpu-supply = <&sw1a_reg>;
> > +};
> > +
> > +&A53_3 {
> > + cpu-supply = <&sw1a_reg>;
> >  };
>
> This should be a separate patch.
>

OK, will send as separate patches in the next version.

> And AFAICS this is wrong, sw1a on the MX8M-EVK is the GPU supply, the
> CPU is supplied by a dedicated switcher that is controlled via a GPIO.
>

Hmm, I think you're right. At least this is what the following document says.

https://www.mouser.com/ds/2/302/IMX8MDQLQEVKHUG-1280333.pdf

So I guess this means there will not be any cpu-supply properties.

Thanks,
Abel

> Regards,
> Lucas
>
> >  &fec1 {
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > index 1a89062..89b2d5f 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > @@ -91,6 +91,7 @@
> >   clocks = <&clk IMX8MQ_CLK_ARM>;
> >   enable-method = "psci";
> >   next-level-cache = <&A53_L2>;
> > + operating-points-v2 = <&a53_0_opp_table>;
> >   };
> >  
> >   A53_1: cpu@1 {
> > @@ -101,6 +102,7 @@
> >   clocks = <&clk IMX8MQ_CLK_ARM>;
> >   enable-method = "psci";
> >   next-level-cache = <&A53_L2>;
> > + operating-points-v2 = <&a53_0_opp_table>;
> >   };
> >  
> >   A53_2: cpu@2 {
> > @@ -111,6 +113,7 @@
> >   clocks = <&clk IMX8MQ_CLK_ARM>;
> >   enable-method = "psci";
> >   next-level-cache = <&A53_L2>;
> > + operating-points-v2 = <&a53_0_opp_table>;
> >   };
> >  
> >   A53_3: cpu@3 {
> > @@ -121,6 +124,7 @@
> >   clocks = <&clk IMX8MQ_CLK_ARM>;
> >   enable-method = "psci";
> >   next-level-cache = <&A53_L2>;
> > + operating-points-v2 = <&a53_0_opp_table>;
> >   };
> >  
> >   A53_L2: l2-cache0 {
> > @@ -666,6 +670,25 @@
> >   status = "disabled";
> >   };
> >  
> > +
> > + a53_0_opp_table: opp-table {
> > + compatible = "operating-points-v2";
> > + opp-shared;
> > +
> > + opp-800000000 {
> > + opp-hz = /bits/ 64 <800000000>;
> > + opp-microvolt = <900000>;
> > + clock-latency-ns = <150000>;
> > + };
> > +
> > + opp-1000000000 {
> > + opp-hz = /bits/ 64 <1000000000>;
> > + opp-microvolt = <900000>;
> > + clock-latency-ns = <150000>;
> > + opp-suspend;
> > + };
> > + };
> > +
> >   gic: interrupt-controller@38800000 {
> >   compatible = "arm,gic-v3";
> >   reg = <0x38800000 0x10000>, /* GIC
> > Dist */
\
 
 \ /
  Last update: 2019-02-14 18:19    [W:0.108 / U:0.656 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site