lkml.org 
[lkml]   [2019]   [Feb]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] nfit: add Hyper-V NVDIMM DSM command set to white list
On Fri, Feb 1, 2019 at 4:34 PM Dexuan Cui <decui@microsoft.com> wrote:
>
> > From: Dan Williams <dan.j.williams@intel.com>
> > Sent: Friday, February 1, 2019 3:47 PM
> > To: Dexuan Cui <decui@microsoft.com>
> >
> > I believe it's the same reason. Without 11189c1089da the _LSR method
> > will fail, and otherwise it works and finds the label that it doesn't
> > like.
> Exactly.
>
> > I'm not seeing "invalid" data in your failure log. Could you double
> > check that it's just not the success of _LSR that causes the issue?
>
> acpi_label_read() never fails for me.
>
> By "invalid", I only mean the messages in the dmesg.bad.txt I previously
> attached (I'm just reading the specs to learn the details about NVDIMM
> namespace's labels, so my description might be inaccurate) :
>
> [ 4.832367] nvdimm nmem1: nsindex0 labelsize 1 invalid
> [ 4.832369] nvdimm nmem1: nsindex1 labelsize 1 invalid

Oh, those are benign. They are a side effect of Linux probing for v1.2
namespace labels vs v1.1. It will always find that one of those is
"invalid".

> ...
> [ 5.259017] nd_pmem namespace0.0: 0x0000000000000000, too small must be at least 0x1000
>
> > > > The regression you are seeing is the fact that the patch enables the kernel
> > to
> > > > enable nvdimm-namespace-label reads.
> > > Yes.
> > >
> > > > Those reads find a namespace index block
> > > > and a label. Unfortunately the label has the LOCAL flag set and Linux
> > > > explicitly ignores pmem namespace labels with that bit set. The reason
> > > Can you please point out the function that ignores the flag?
> > >
> > > I checked where NSLABEL_FLAG_LOCAL is used, but it looks I can't find a
> > > related function.
> >
> > scan_labels() is where the namespace label is validated relative to
> > the region type:
> >
> > if (is_nd_blk(&nd_region->dev)
> > == !!(flags & NSLABEL_FLAG_LOCAL))
> > /* pass, region matches label type */;
> > else
> > continue;
> >
> > It also has meaning for the namespace capacity allocation
> > implementation that needed that flag to distinguish aliased capacity
> > between Block Aperture Mode and PMEM Mode access.
> Thanks for the pointer! I'm looking at this function.
>
> > > > for that is due to the fact that the original definition of the LOCAL
> > > > bit from v1.1 of the namespace label implementation [1] explicitly
> > > > limited the LOCAL flag to "block aperture" regions. If you clear that
> > > > LOCAL flag I expect it will work. To my knowledge Windows pretends
> > > > that the v1.1 definition never existed.
> > > I'm trying to find out where the flag is used and how to clear it.
> >
> > Assuming Hyper-V implements _LSW, you can recreate / reinitialize the
> > label area:
>
> I think Hyper-V only implements _LSR:
> [ 4.720623] nfit ACPI0012:00: device:00: has _LSR
> [ 4.723683] nfit ACPI0012:00: device:01: has _LSR

That's unfortunate...

>
> > > > The UEFI 2.7 specification for v1.2 labels states that setting the
> > > > LOCAL flag is optional when "nlabel", number of labels in the set, is
> > > > 1. Linux makes that mandatory as LOCAL is redundant when nlabel is 1.
> > > >
> > > > That said, the Robustness Principle makes a case that Linux should
> > > > tolerate the bit being set. However, it's just a non-trivial amount of
> > > > work to unwind the ingrained block-aperture assumptions of that bit.
> > > Can you please explain this a bit more? Sorry, I'm new to this area...
> >
> > The short story is that Linux enforces that LOCAL == Block Mode
> > Namespaces. See section 2.2 Namespace Label Layout in the original
> > spec [1]. The EFI 2.7 definition tried to allow for LOCAL to be set
> > when an interleave-set was comprised of a single NVDIMM, but then also
> > states its optional when Nlabel is 1. It has zero functional use for
> > interleave-set based namespaces even when the interleave-set-width is
> > 1. So Linux takes the option to never set it, and goes further to
> > reject it if it's set and the region-type does not match, because that
> > follows the v1.1 meaning of the flag.
> >
> > [1]:
> Thanks for the link! I'll read it.
> BTW, it looks Hyper-V only supports PMEM namespace, at least so far.

I don't think it should bother. It only makes sense for bare metal and
even then I know of no NVDIMMs that are shipping it.

\
 
 \ /
  Last update: 2019-02-02 01:48    [W:0.108 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site