lkml.org 
[lkml]   [2019]   [Dec]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2 1/7] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
On Thu 19 Dec 02:41 PST 2019, Sricharan R wrote:

> Add device tree binding Documentation details for ipq6018
> pinctrl driver.
>
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
>
> [V2] Splitted dt bindings and driver into different patches. Added missing bindings,
> and some style changes.
>
> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 172 +++++++++++++++++++++
> 1 file changed, 172 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> new file mode 100644
> index 0000000..745a11e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> @@ -0,0 +1,172 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
> +
> +maintainers:
> + - Sricharan R <sricharan@codeaurora.org>
> +
> +description: |
> + This binding describes the Top Level Mode Multiplexer block found in the
> + IPQ6018 platform.
> +
> +properties:
> + compatible:
> + const: qcom,ipq6018-pinctrl
> + reg:
> + maxItems: 1
> + interrupts:
> + Description: Specifies the TLMM summary IRQ
> + maxItems: 1
> + interrupt-controller: true
> + '#interrupt-cells':
> + Description:
> + Specifies the PIN numbers and Flags, as defined in defined in
> + include/dt-bindings/interrupt-controller/irq.h
> + const: 2
> + gpio-controller: true
> + '#gpio-cells':
> + Description: Specifying the pin number and flags, as defined in
> + include/dt-bindings/gpio/gpio.h
> + const: 2
> + gpio-ranges:
> + Description: Documentation/devicetree/bindings/gpio/gpio.txt
> + maxItems: 1
> +
> +#PIN CONFIGURATION NODES
> +patternProperties:
> + '-pins$':
> + type: object
> + Description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> +
> + Properties:
> + pins:
> + allOf:
> + $ref: /schemas/types.yaml#/definitions/string
> + enum:
> + gpio0-gpio80
> + sdc1_clk
> + sdc1_cmd
> + sdc1_data
> + sdc2_clk
> + sdc2_cmd
> + sdc2_data
> + qdsd_cmd
> + qdsd_data0
> + qdsd_data1
> + qdsd_data2
> + qdsd_data3
> + Description:
> + List of gpio pins affected by the properties specified in this
> + subnode.
> +
> + function:
> + allOf:
> + $ref: /schemas/types.yaml#/definitions/string
> + enum:
> + adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
> + blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1,
> + blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
> + blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
> + blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
> + blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst
> + Description:
> + Specify the alternative function to be configured for the specified
> + pins.
> + bias-disable:

Is there any way to inherit these from some common definition?

> + type: boolean
> + Description:
> + The specified pins should be configured as no pull.
> + bias-pull-down:
> + type: boolean
> + Description:
> + The specified pins should be configured as pull down.
> + bias-pull-up:
> + type: boolean
> + Description:
> + The specified pins should be configured as pull up.
> + output-high:
> + type: boolean
> + Description:
> + The specified pins are configured in output mode, driven high.
> + This option is not available for sdc pins.
> + output-low:
> + type: boolean
> + Description:
> + The specified pins are configured in output mode, driven low.
> + This option is not available for sdc pins.
> + drive-strength:
> + allOf:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> + Description:
> + elects the drive strength for the specified pins, in mA.

Selects?

> +
> + required:
> + - pins
> + - function
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - interrupt-controller
> + - '#interrupt-cells'
> + - gpio-controller
> + - '#gpio-cells'
> + - gpio-ranges
> +
> +example:
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,ipq6018-pinctrl";
> + reg = <0x1000000 0x300000>;
> + interrupts = <0 208 0>;

<GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>

> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + uart_pins: uart_pins {

s/_/- in the node name.

> + mux {
> + pins = "gpio4", "gpio5";
> + function = "blsp_uart2";

Duplicate the function definition in tx and rx and drop the "mux" node.

Regards,
Bjorn

> + };
> +
> + tx {
> + pins = "gpio4";
> + drive-strength = <4>;
> + bias-disable;
> + };
> +
> + rx {
> + pins = "gpio5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> + };
> --
> 1.9.1

\
 
 \ /
  Last update: 2019-12-29 04:42    [W:0.158 / U:6.820 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site