lkml.org 
[lkml]   [2019]   [Dec]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 5/5] arm64: dts: Add Unisoc's SC9863A SoC support
On Mon, Nov 25, 2019 at 2:34 AM Chunyan Zhang <zhang.lyra@gmail.com> wrote:
>
> On Fri, 15 Nov 2019 at 22:43, Rob Herring <robh@kernel.org> wrote:
> >
> > On Fri, Nov 15, 2019 at 2:59 AM Chunyan Zhang <zhang.lyra@gmail.com> wrote:
> > >
> > > On Fri, 15 Nov 2019 at 05:05, Rob Herring <robh@kernel.org> wrote:
> > > >
> > > > On Mon, Nov 11, 2019 at 05:02:30PM +0800, Chunyan Zhang wrote:
> > > > >
> > > > > Add basic DT to support Unisoc's SC9863A, with this patch,
> > > > > the board sp9863a-1h10 can run into console.
> > > > >
> > > > > Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
> > > > > ---
> > > > > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > > > > arch/arm64/boot/dts/sprd/sc9863a.dtsi | 536 ++++++++++++++++++++++
> > > > > arch/arm64/boot/dts/sprd/sharkl3.dtsi | 188 ++++++++
> > > > > arch/arm64/boot/dts/sprd/sp9863a-1h10.dts | 40 ++
> > > > > 4 files changed, 766 insertions(+), 1 deletion(-)
> > > > > create mode 100644 arch/arm64/boot/dts/sprd/sc9863a.dtsi
> > > > > create mode 100644 arch/arm64/boot/dts/sprd/sharkl3.dtsi
> > > > > create mode 100644 arch/arm64/boot/dts/sprd/sp9863a-1h10.dts
> > > > >
> > > > > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > > > > index 2bdc23804f40..f4f1f5148cc2 100644
> > > > > --- a/arch/arm64/boot/dts/sprd/Makefile
> > > > > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > > > > @@ -1,3 +1,4 @@
> > > > > # SPDX-License-Identifier: GPL-2.0
> > > > > dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > > > > - sp9860g-1h10.dtb
> > > > > + sp9860g-1h10.dtb \
> > > > > + sp9863a-1h10.dtb
> > > > > diff --git a/arch/arm64/boot/dts/sprd/sc9863a.dtsi b/arch/arm64/boot/dts/sprd/sc9863a.dtsi
> > > > > new file mode 100644
> > > > > index 000000000000..578d71a932d9
> > > > > --- /dev/null
> > > > > +++ b/arch/arm64/boot/dts/sprd/sc9863a.dtsi
> > > > > @@ -0,0 +1,536 @@
> > > > > +// SPDX-License-Identifier: GPL-2.0-only
> > > > > +/*
> > > > > + * Unisoc SC9863A SoC DTS file
> > > > > + *
> > > > > + * Copyright (C) 2019, Unisoc Inc.
> > > > > + */
> > > > > +
> > > > > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > > > > +#include "sharkl3.dtsi"
> > > > > +
> > > > > +/ {
> > > > > + cpus {
> > > > > + #address-cells = <2>;
> > > > > + #size-cells = <0>;
> > > > > +
> > > > > + cpu-map {
> > > > > + cluster0 {
> > > > > + core0 {
> > > > > + cpu = <&CPU0>;
> > > > > + };
> > > > > + core1 {
> > > > > + cpu = <&CPU1>;
> > > > > + };
> > > > > + core2 {
> > > > > + cpu = <&CPU2>;
> > > > > + };
> > > > > + core3 {
> > > > > + cpu = <&CPU3>;
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + cluster1 {
> > > > > + core0 {
> > > > > + cpu = <&CPU4>;
> > > > > + };
> > > > > + core1 {
> > > > > + cpu = <&CPU5>;
> > > > > + };
> > > > > + core2 {
> > > > > + cpu = <&CPU6>;
> > > > > + };
> > > > > + core3 {
> > > > > + cpu = <&CPU7>;
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + CPU0: cpu@0 {
> > > > > + device_type = "cpu";
> > > > > + compatible = "arm,cortex-a55";
> > > > > + reg = <0x0 0x0>;
> > > > > + enable-method = "psci";
> > > > > + cpu-idle-states = <&CORE_PD>;
> > > > > + };
> > > > > +
> > > > > + CPU1: cpu@100 {
> > > >
> > > > Your numbering seems odd. This follows the MPIDR reg? Normally a cluster
> > > > would share the same number in one of the bytes.
> > >
> > > We're using A55, and the spec says that bit[15:8] identifies
> > > individual cores within the local DynamIQ™ cluster
> >
> > Okay.
> >
> > > Also, we only support one cluster.
> >
> > cpu-map shows 2 clusters.
>
> From the scheduler view, we have two clusters, but there's actually
> one physical cluster only.

What's the scheduler? ;)

DT describes the physical system.

Rob

\
 
 \ /
  Last update: 2019-12-02 17:35    [W:0.060 / U:10.308 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site