lkml.org 
[lkml]   [2019]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] leds: lm3692x: Allow to set ovp and brigthness mode
From
Date
Guido

On 12/16/19 6:28 AM, Guido Günther wrote:
> Overvoltage protection and brightness mode are currently hardcoded
> as disabled in the driver. Make these configurable via DT.

Can we split these up to two separate patch series?

We are adding 2 separate features and if something is incorrect with one
of the changes it is a bit hard to debug.

>
> Signed-off-by: Guido Günther <agx@sigxcpu.org>
> ---
> drivers/leds/leds-lm3692x.c | 43 +++++++++++++++++++++++++++++++------
> 1 file changed, 37 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/leds/leds-lm3692x.c b/drivers/leds/leds-lm3692x.c
> index 8b408102e138..2c084b333628 100644
> --- a/drivers/leds/leds-lm3692x.c
> +++ b/drivers/leds/leds-lm3692x.c
> @@ -114,6 +114,7 @@ struct lm3692x_led {
> struct regulator *regulator;
> int led_enable;
> int model_id;
> + u8 boost_ctrl, brightness_ctrl;
> };
>
> static const struct reg_default lm3692x_reg_defs[] = {
> @@ -249,10 +250,7 @@ static int lm3692x_init(struct lm3692x_led *led)
> if (ret)
> goto out;
>
> - ret = regmap_write(led->regmap, LM3692X_BOOST_CTRL,
> - LM3692X_BOOST_SW_1MHZ |
> - LM3692X_BOOST_SW_NO_SHIFT |
> - LM3692X_OCP_PROT_1_5A);
> + ret = regmap_write(led->regmap, LM3692X_BOOST_CTRL, led->boost_ctrl);
> if (ret)
> goto out;

regmap_update_bits


>
> @@ -268,8 +266,7 @@ static int lm3692x_init(struct lm3692x_led *led)
> if (ret)
> goto out;
>
> - ret = regmap_write(led->regmap, LM3692X_BRT_CTRL,
> - LM3692X_BL_ADJ_POL | LM3692X_RAMP_EN);
> + ret = regmap_write(led->regmap, LM3692X_BRT_CTRL, led->brightness_ctrl);
> if (ret)
> goto out;
regmap_update_bits
>
> @@ -326,6 +323,8 @@ static int lm3692x_probe_dt(struct lm3692x_led *led)
> {
> struct fwnode_handle *child = NULL;
> struct led_init_data init_data = {};
> + u32 ovp = 0;
> + bool exp_mode;
> int ret;
>
> led->enable_gpio = devm_gpiod_get_optional(&led->client->dev,
> @@ -350,6 +349,38 @@ static int lm3692x_probe_dt(struct lm3692x_led *led)
> led->regulator = NULL;
> }
>
> + led->boost_ctrl = LM3692X_BOOST_SW_1MHZ |
> + LM3692X_BOOST_SW_NO_SHIFT |
> + LM3692X_OCP_PROT_1_5A;
Make this a #define and then it can be reused as a mask for
regmap_update_bits
> + ret = device_property_read_u32(&led->client->dev,
> + "ti,overvoltage-volts", &ovp);
> + if (!ret) {

if (ret)

    set boost_ctrl to default value since the default is not 0

led->boost_ctrl |= LM3692X_OVP_29V;

else

     do case

> + switch (ovp) {
> + case 0:
> + break;
> + case 22:
If the value is 21v why is this case 22?  DT binding says 21 is the
first value
> + led->boost_ctrl |= LM3692X_OVP_21V;
> + break;
> + case 25:
> + led->boost_ctrl |= LM3692X_OVP_25V;
> + break;
> + case 29:
> + led->boost_ctrl |= LM3692X_OVP_29V;
> + break;
> + default:
> + dev_err(&led->client->dev, "Invalid OVP %d\n", ovp);
> + return -EINVAL;
> + }
> + }
> + dev_dbg(&led->client->dev, "OVP: %dV", ovp);
> +
extra debug statement
> + led->brightness_ctrl = LM3692X_BL_ADJ_POL | LM3692X_RAMP_EN;
Same comment as before on the #define
> + exp_mode = device_property_read_bool(&led->client->dev,
> + "ti,brightness-mapping-exponential");
> + dev_dbg(&led->client->dev, "Exponential brightness: %d", exp_mode);

extra debug statement

Dan


\
 
 \ /
  Last update: 2019-12-17 13:57    [W:0.159 / U:0.816 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site