lkml.org 
[lkml]   [2019]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH AUTOSEL 4.19 120/205] usb: mtu3: disable vbus rise/fall interrupts of ltssm
Date
From: Chunfeng Yun <chunfeng.yun@mediatek.com>

[ Upstream commit 0eae49582b4dee1a0e96007e1dea5122db98371a ]

The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/usb/mtu3/mtu3_core.c | 4 ++--
drivers/usb/mtu3/mtu3_gadget.c | 22 ++++++++++++++--------
2 files changed, 16 insertions(+), 10 deletions(-)

diff --git a/drivers/usb/mtu3/mtu3_core.c b/drivers/usb/mtu3/mtu3_core.c
index 48d10a61e271c..8606935201326 100644
--- a/drivers/usb/mtu3/mtu3_core.c
+++ b/drivers/usb/mtu3/mtu3_core.c
@@ -185,8 +185,8 @@ static void mtu3_intr_enable(struct mtu3 *mtu)

if (mtu->is_u3_ip) {
/* Enable U3 LTSSM interrupts */
- value = HOT_RST_INTR | WARM_RST_INTR | VBUS_RISE_INTR |
- VBUS_FALL_INTR | ENTER_U3_INTR | EXIT_U3_INTR;
+ value = HOT_RST_INTR | WARM_RST_INTR |
+ ENTER_U3_INTR | EXIT_U3_INTR;
mtu3_writel(mbase, U3D_LTSSM_INTR_ENABLE, value);
}

diff --git a/drivers/usb/mtu3/mtu3_gadget.c b/drivers/usb/mtu3/mtu3_gadget.c
index 5c60a8c5a0b5c..bbcd3332471dc 100644
--- a/drivers/usb/mtu3/mtu3_gadget.c
+++ b/drivers/usb/mtu3/mtu3_gadget.c
@@ -585,6 +585,17 @@ static const struct usb_gadget_ops mtu3_gadget_ops = {
.udc_stop = mtu3_gadget_stop,
};

+static void mtu3_state_reset(struct mtu3 *mtu)
+{
+ mtu->address = 0;
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+ mtu->may_wakeup = 0;
+ mtu->u1_enable = 0;
+ mtu->u2_enable = 0;
+ mtu->delayed_status = false;
+ mtu->test_mode = false;
+}
+
static void init_hw_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
u32 epnum, u32 is_in)
{
@@ -702,6 +713,7 @@ void mtu3_gadget_disconnect(struct mtu3 *mtu)
spin_lock(&mtu->lock);
}

+ mtu3_state_reset(mtu);
usb_gadget_set_state(&mtu->g, USB_STATE_NOTATTACHED);
}

@@ -712,12 +724,6 @@ void mtu3_gadget_reset(struct mtu3 *mtu)
/* report disconnect, if we didn't flush EP state */
if (mtu->g.speed != USB_SPEED_UNKNOWN)
mtu3_gadget_disconnect(mtu);
-
- mtu->address = 0;
- mtu->ep0_state = MU3D_EP0_STATE_SETUP;
- mtu->may_wakeup = 0;
- mtu->u1_enable = 0;
- mtu->u2_enable = 0;
- mtu->delayed_status = false;
- mtu->test_mode = false;
+ else
+ mtu3_state_reset(mtu);
}
--
2.20.1
\
 
 \ /
  Last update: 2019-11-08 12:41    [W:0.446 / U:1.400 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site