lkml.org 
[lkml]   [2019]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/4] Bluetooth: hci_bcm: Disallow set_baudrate for BCM4354
From
Date
Hi Abhishek,

> Without updating the patchram, the BCM4354 does not support a higher
> operating speed. The normal bcm_setup follows the correct order
> (init_speed, patchram and then oper_speed) but the serdev driver will
> set the operating speed before calling the hu->setup function. Thus,
> for the BCM4354, disallow setting the operating speed before patchram.
>
> Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
> ---
>
> Changes in v2: None
>
> drivers/bluetooth/hci_bcm.c | 25 +++++++++++++++++++++++--
> 1 file changed, 23 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c
> index 0f851c0dde7f..2114df607cb3 100644
> --- a/drivers/bluetooth/hci_bcm.c
> +++ b/drivers/bluetooth/hci_bcm.c
> @@ -1167,7 +1167,7 @@ static int bcm_remove(struct platform_device *pdev)
> return 0;
> }
>
> -static const struct hci_uart_proto bcm_proto = {
> +static struct hci_uart_proto bcm_proto = {
> .id = HCI_UART_BCM,
> .name = "Broadcom",
> .manufacturer = 15,
> @@ -1371,6 +1371,24 @@ static struct platform_driver bcm_driver = {
> },
> };
>
> +#define BCM_QUIRK_DISALLOW_SET_BAUDRATE (1 << 0)
> +const u32 disallow_set_baudrate = BCM_QUIRK_DISALLOW_SET_BAUDRATE;
> +
> +static int bcm_check_disallow_set_baudrate(struct serdev_device *serdev)
> +{
> + const u32 *quirks = device_get_match_data(&serdev->dev);
> +
> + if (quirks) {
> + /* BCM4354 can't run at full speed before patchram. Disallow
> + * externally setting operating speed.
> + */
> + if (*quirks & BCM_QUIRK_DISALLOW_SET_BAUDRATE)
> + return 1;
> + }
> +
> + return 0;
> +}
> +
> static int bcm_serdev_probe(struct serdev_device *serdev)
> {
> struct bcm_device *bcmdev;
> @@ -1408,6 +1426,9 @@ static int bcm_serdev_probe(struct serdev_device *serdev)
> if (err)
> dev_err(&serdev->dev, "Failed to power down\n");
>
> + if (bcm_check_disallow_set_baudrate(serdev))
> + bcm_proto.set_baudrate = NULL;
> +

this change is not allowed since bcm_proto is on purpose const.

> return hci_uart_register_device(&bcmdev->serdev_hu, &bcm_proto);
> }
>
> @@ -1424,7 +1445,7 @@ static const struct of_device_id bcm_bluetooth_of_match[] = {
> { .compatible = "brcm,bcm4345c5" },
> { .compatible = "brcm,bcm4330-bt" },
> { .compatible = "brcm,bcm43438-bt" },
> - { .compatible = "brcm,bcm43540-bt" },
> + { .compatible = "brcm,bcm43540-bt", .data = &disallow_set_baudrate },
> { },
> };
> MODULE_DEVICE_TABLE(of, bcm_bluetooth_of_match);

So I would prefer if we do this in a more generic from that will make this easy to extend in the future. Similar to what hci_qca.c does actually with defining a separate struct for the module differences.

struct bcm_device_data (
bool no_early_oper_speed;
};

static const struct bcm_device_data bcm43540_device {
.no_early_oper_speed = true,
};

static const struct of_device_id bcm_bluetooth_of_match[] = {
..
{ .compatible = "brcm,bcm43540-bt", .data = &bcm43540_device },
( },
};

And then load the struct in serdev probe as pointer and check its existence and add the struct bcm_device_data to struct bcm_device so it can be referenced when you change the baudrate.

Regards

Marcel

\
 
 \ /
  Last update: 2019-11-08 07:09    [W:0.060 / U:0.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site