Messages in this thread | | | Subject | Re: [PATCH 1/1] ARM: dts: am5729: beaglebone-ai: adding device tree | From | Grygorii Strashko <> | Date | Fri, 22 Nov 2019 11:29:58 +0200 |
| |
On 21/11/2019 16:41, Robey, Caleb wrote: > > >> -----Original Message----- >> From: Strashko, Grygorii >> Sent: Thursday, November 21, 2019 5:05 AM >> To: Robey, Caleb; linux-omap@vger.kernel.org >> Cc: Jason Kridner; Vutla, Lokesh; Kridner, Jason; Rizvi, Mohammad Faiz >> Abbas; Dannenberg, Andreas; Hiblot, Jean-Jacques; Bajjuri, Praneeth; Davis, >> Andrew; Tom Rini; Robert Nelson; Rob Herring; Mark Rutland; Benoît >> Cousson; Tony Lindgren; devicetree@vger.kernel.org; linux- >> kernel@vger.kernel.org >> Subject: Re: [PATCH 1/1] ARM: dts: am5729: beaglebone-ai: adding device >> tree >> >> >> >> On 19/11/2019 22:28, Caleb Robey wrote: >>> From: Jason Kridner <jdk@ti.com> >>> >>> BeagleBoard.org BeagleBone AI is an open source hardware single >>> board computer based on the Texas Instruments AM5729 SoC featuring >>> dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital >>> signal processor (DSP), quad-core embedded vision engine (EVE), >>> Arm Cortex-M4 processors, dual programmable realtime unit >>> industrial control subsystems and more. The board features 1GB >>> DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, >>> 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion >>> headers. >>> >>> For more information, refer to: >>> https://beaglebone.ai >> >> >>> >>> This patch introduces the BeagleBone AI device tree. >>> >>> Note that the device use the "ti,tpd12s016" component which is >>> software compatible with "ti,tpd12s015". Thus we only use the >>> latter driver. >>> >>> Signed-off-by: Jason Kridner <jdk@ti.com> >>> Signed-off-by: Caleb Robey <c-robey@ti.com> >>> Cc: Robert Nelson <robertcnelson@gmail.com> >>> >>> --- >>> arch/arm/boot/dts/Makefile | 1 + >>> arch/arm/boot/dts/am5729-beagleboneai.dts | 782 >> ++++++++++++++++++++++ >>> 2 files changed, 783 insertions(+) >>> create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts >>> >>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >>> index b21b3a64641a..b1154dbda73c 100644 >>> --- a/arch/arm/boot/dts/Makefile >>> +++ b/arch/arm/boot/dts/Makefile >> >> [..] >> >>> + >>> +&uart1 { >>> + status = "okay"; >>> +}; >>> + >>> +&davinci_mdio { >>> + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; >>> + reset-delay-us = <2>; >>> + >>> + phy0: ethernet-phy@1 { >>> + reg = <4>; >>> + compatible = "ethernet-phy-id004d.d072", >>> + "ethernet-phy-ieee802.3-c22"; >> >> Pls, do not ignore my comments. >> >> Above compatible should not be required. > > Grygori, I am so sorry about this - I had deleted this, > but must have made a mistake in the resubmission. I > will fix it immediately. >
Yep. thanks and sorry. I saw you fixed it in next version.
-- Best regards, grygorii
| |