lkml.org 
[lkml]   [2019]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc
From
Date
Hi Doug,

Am 18.11.19 um 17:08 schrieb Doug Anderson:
> Hi,
>
>
> On Fri, Nov 15, 2019 at 3:19 AM Heiko Stübner <heiko@sntech.de> wrote:
>>
>> Hi Markus,
>>
>> Am Freitag, 15. November 2019, 11:37:58 CET schrieb Markus Reichl:
>> > Am 14.11.19 um 14:10 schrieb Heiko Stuebner:
>> > > $subject is missing the [PATCH] prefix
>> > will fix.
>>
>> no need to resend just for this ... just to keep in mind for future patches ;-)
>>
>>
>> > > Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
>> > >> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
>> > >>
>> > >> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
>> > >> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
>> > >> mmc1: "running CQE recovery", even hangs with damaged fs,
>> > >> when running under heavy load, e.g. compiling kernel.
>> > >> Both run fine with HS200.
>> > >>
>> > >> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
>> > >> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3
>> > >
>> > > I'm hoping for some input from other people in Cc but your mail headers
>> > > also referenced the drive-impendance series from Christoph [0], which
>> > > it seems we need to poke the phy maintainer again.
>> > >
>> > > Did you check if changing the impedance helped (like the signal dampening
>> > > Philipp described in one of the replies there).
>> >
>> > checked with
>> >
>> > &emmc_phy {
>> > + drive-impedance-ohm = <33>;
>> >
>> > gives no improvement:
>>
>> That is sad ... I guess we really should disable hs400 then ...
>> that may give others more incentive to dive deeper ;-)
>
> Just out of curiosity, is the problem with the strobe line, or with
> hs400? Have you tried using the solution from "rk3399-gru.dtsi"?
> Namely:
>
> /*
> * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
> * same (or nearly the same) performance for all eMMC that are intended
> * to be used.
> */
> assigned-clock-rates = <150000000>;
>
> IIRC hs400 on rk3399 was a bit iffy but running at 150 MHz made it
> much more reliable and still gave you 300 MB/s transfer rate (so much
> better than hs200). In reality many eMMC chips can't do > 300 MB/s
> anyway.
>
I tried 150000000 and 100000000, but it did not help.

Gruß,
--
Markus

> -Doug
>

\
 
 \ /
  Last update: 2019-11-18 20:06    [W:0.073 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site