lkml.org 
[lkml]   [2019]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/4] spi: spi-mem: Add support for Octal 8D-8D-8D mode
Date
According to JESD216C SPI NORs are using 2 bytes opcodes
when operated in OPI (Octal Peripheral Interface).

To add extension command, command bytes number and
Double Transfer Rate(DTR) fields to the spi_mem_op struct.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
---
drivers/spi/spi-mem.c | 8 +++++++-
include/linux/spi/spi-mem.h | 13 +++++++++++++
2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index 9f0fa9f..eb33dd85 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c
@@ -154,6 +154,12 @@ bool spi_mem_default_supports_op(struct spi_mem *mem,
op->data.dir == SPI_MEM_DATA_OUT))
return false;

+ if (op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr)
+ return false;
+
+ if (op->cmd.nbytes != 1)
+ return false;
+
return true;
}
EXPORT_SYMBOL_GPL(spi_mem_default_supports_op);
@@ -168,7 +174,7 @@ static bool spi_mem_buswidth_is_valid(u8 buswidth)

static int spi_mem_check_op(const struct spi_mem_op *op)
{
- if (!op->cmd.buswidth)
+ if (!op->cmd.buswidth || op->cmd.nbytes < 1 || op->cmd.nbytes > 2)
return -EINVAL;

if ((op->addr.nbytes && !op->addr.buswidth) ||
diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index af9ff2f..bf54079 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h
@@ -17,6 +17,7 @@
{ \
.buswidth = __buswidth, \
.opcode = __opcode, \
+ .nbytes = 1, \
}

#define SPI_MEM_OP_ADDR(__nbytes, __val, __buswidth) \
@@ -69,11 +70,15 @@ enum spi_mem_data_dir {

/**
* struct spi_mem_op - describes a SPI memory operation
+ * @cmd.nbytes: number of opcode bytes (only 1 or 2 are valid)
* @cmd.buswidth: number of IO lines used to transmit the command
+ * @cmd.dtr: set true to transfer opcode in double transfer rate mode
* @cmd.opcode: operation opcode
+ * @cmd.ext_opcode: extension operation opcode
* @addr.nbytes: number of address bytes to send. Can be zero if the operation
* does not need to send an address
* @addr.buswidth: number of IO lines used to transmit the address cycles
+ * @addr.dtr: set true to transfer address bytes in double transfer rate mode
* @addr.val: address value. This value is always sent MSB first on the bus.
* Note that only @addr.nbytes are taken into account in this
* address value, so users should make sure the value fits in the
@@ -81,34 +86,42 @@ enum spi_mem_data_dir {
* @dummy.nbytes: number of dummy bytes to send after an opcode or address. Can
* be zero if the operation does not require dummy bytes
* @dummy.buswidth: number of IO lanes used to transmit the dummy bytes
+ * @dummy.dtr: set true to transfer dummy bytes in double transfer rate mode
* @data.buswidth: number of IO lanes used to send/receive the data
* @data.dir: direction of the transfer
* @data.nbytes: number of data bytes to send/receive. Can be zero if the
* operation does not involve transferring data
+ * @data.dtr: set true to transfer data bytes in double transfer rate mode
* @data.buf.in: input buffer (must be DMA-able)
* @data.buf.out: output buffer (must be DMA-able)
*/
struct spi_mem_op {
struct {
+ u8 nbytes;
u8 buswidth;
+ bool dtr;
u8 opcode;
+ u8 ext_opcode;
} cmd;

struct {
u8 nbytes;
u8 buswidth;
+ bool dtr;
u64 val;
} addr;

struct {
u8 nbytes;
u8 buswidth;
+ bool dtr;
} dummy;

struct {
u8 buswidth;
enum spi_mem_data_dir dir;
unsigned int nbytes;
+ bool dtr;
union {
void *in;
const void *out;
--
1.9.1
\
 
 \ /
  Last update: 2019-11-15 09:59    [W:0.170 / U:4.736 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site