lkml.org 
[lkml]   [2019]   [Nov]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] drm/msm/mdp5: enable autocommit
On Tue, Nov 12, 2019 at 08:38:27AM -0700, Jeffrey Hugo wrote:
> On Tue, Nov 12, 2019 at 3:49 AM Brian Masney <masneyb@onstation.org> wrote:
> >
> > Since the introduction of commit 2d99ced787e3 ("drm/msm: async commit
> > support"), command-mode panels began throwing the following errors:
> >
> > msm fd900000.mdss: pp done time out, lm=0
> >
> > Let's fix this by enabling the autorefresh feature that's available in
> > the MDP starting at version 1.0. This will cause the MDP to
> > automatically send a frame to the panel every time the panel invokes
> > the TE signal, which will trigger the PP_DONE IRQ. This requires not
> > sending a START signal for command-mode panels.
> >
> > This fixes the error and gives us a counter for command-mode panels that
> > we can use to implement async commit support for the MDP5 in a follow up
> > patch.
> >
> > Signed-off-by: Brian Masney <masneyb@onstation.org>
> > Suggested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
> > ---
> > drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c | 15 ++++++++++++++-
> > drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c | 9 +--------
> > 2 files changed, 15 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
> > index 05cc04f729d6..539348cb6331 100644
> > --- a/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
> > +++ b/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
> > @@ -456,6 +456,7 @@ static void mdp5_crtc_atomic_enable(struct drm_crtc *crtc,
> > {
> > struct mdp5_crtc *mdp5_crtc = to_mdp5_crtc(crtc);
> > struct mdp5_crtc_state *mdp5_cstate = to_mdp5_crtc_state(crtc->state);
> > + struct mdp5_pipeline *pipeline = &mdp5_cstate->pipeline;
> > struct mdp5_kms *mdp5_kms = get_kms(crtc);
> > struct device *dev = &mdp5_kms->pdev->dev;
> >
> > @@ -493,9 +494,21 @@ static void mdp5_crtc_atomic_enable(struct drm_crtc *crtc,
> >
> > mdp_irq_register(&mdp5_kms->base, &mdp5_crtc->err);
> >
> > - if (mdp5_cstate->cmd_mode)
> > + if (mdp5_cstate->cmd_mode) {
> > mdp_irq_register(&mdp5_kms->base, &mdp5_crtc->pp_done);
> >
> > + /*
> > + * Enable autorefresh so we get regular ping/pong IRQs.
> > + * - Bit 31 is the enable bit
> > + * - Bits 0-15 represent the frame count, specifically how many
> > + * TE events before the MDP sends a frame.
> > + */
> > + mdp5_write(mdp5_kms,
> > + REG_MDP5_PP_AUTOREFRESH_CONFIG(pipeline->mixer->pp),
> > + BIT(31) | BIT(0));
> > + crtc_flush_all(crtc);
> > + }
> > +
> > mdp5_crtc->enabled = true;
> > }
> >
> > diff --git a/drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c b/drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c
> > index 030279d7b64b..aee295abada3 100644
> > --- a/drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c
> > +++ b/drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c
> > @@ -187,14 +187,7 @@ static bool start_signal_needed(struct mdp5_ctl *ctl,
> > if (!ctl->encoder_enabled)
> > return false;
> >
> > - switch (intf->type) {
> > - case INTF_WB:
> > - return true;
> > - case INTF_DSI:
> > - return intf->mode == MDP5_INTF_DSI_MODE_COMMAND;
> > - default:
> > - return false;
> > - }
> > + return intf->type == INTF_WB;
> > }
>
> I don't think this fully works.
>
> The whole "flush" thing exists because the configuration is double
> buffered. You write to the flush register to tell the hardware to
> pickup the new configuration, but it doesn't do that automatically.
> It only picks up the new config on the next "vsync". When you have a
> video mode panel, you have the timing engine running, which drives
> that. With a command mode panel, you have either the start signal, or
> the auto refresh to do the same, but you have a bit of a chicken and
> egg situation where if you are programming the hardware from scratch,
> autorefresh isn't already enabled to then pickup the config to enable
> autorefresh. In this case, you'll need a single start to kick
> everything off. However, if say the bootloader already configured
> things and has autorefresh running, then you need to not do that start
> because you'll overload the DSI like you saw.

As part of my testing for this work, I added a log statement to
mdp5_crtc_pp_done_irq() and it shows that a PP_IRQ comes in consistently
every ~0.0166 seconds, which is about 60 HZ. Without this change, plus
the 3 commits I mentioned in an earlier email related to the async
commit support, the PP IRQs come in at a variety of times: between every
~0.0140 and ~0.2224 seconds. That's why I assumed that this was working.

If I call send_start_signal() inside mdp5_crtc_atomic_enable(), then the
display does not work properly.

> Nothing is simple, is it? :)

Ain't that the truth...

Brian

\
 
 \ /
  Last update: 2019-11-13 12:24    [W:0.072 / U:0.348 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site