lkml.org 
[lkml]   [2019]   [Oct]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v8 3/5] mfd: ioc3: Add driver for SGI IOC3 chip
Date
SGI IOC3 chip has integrated ethernet, keyboard and mouse interface.
It also supports connecting a SuperIO chip for serial and parallel
interfaces. IOC3 is used inside various SGI systemboards and add-on
cards with different equipped external interfaces.

Support for ethernet and serial interfaces were implemented inside
the network driver. This patchset moves out the not network related
parts to a new MFD driver, which takes care of card detection,
setup of platform devices and interrupt distribution for the subdevices.

Serial portion: Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
---
arch/mips/sgi-ip27/ip27-timer.c | 20 --
drivers/mfd/Kconfig | 13 +
drivers/mfd/Makefile | 1 +
drivers/mfd/ioc3.c | 588 ++++++++++++++++++++++++++++++++++++
drivers/net/ethernet/sgi/Kconfig | 5 +-
drivers/net/ethernet/sgi/ioc3-eth.c | 561 ++++++----------------------------
drivers/tty/serial/8250/8250_ioc3.c | 98 ++++++
drivers/tty/serial/8250/Kconfig | 11 +
drivers/tty/serial/8250/Makefile | 1 +
9 files changed, 813 insertions(+), 485 deletions(-)
create mode 100644 drivers/mfd/ioc3.c
create mode 100644 drivers/tty/serial/8250/8250_ioc3.c

diff --git a/arch/mips/sgi-ip27/ip27-timer.c b/arch/mips/sgi-ip27/ip27-timer.c
index 9b4b9ac621a3..5631e93ea350 100644
--- a/arch/mips/sgi-ip27/ip27-timer.c
+++ b/arch/mips/sgi-ip27/ip27-timer.c
@@ -188,23 +188,3 @@ void hub_rtc_init(cnodeid_t cnode)
LOCAL_HUB_S(PI_RT_PEND_B, 0);
}
}
-
-static int __init sgi_ip27_rtc_devinit(void)
-{
- struct resource res;
-
- memset(&res, 0, sizeof(res));
- res.start = XPHYSADDR(KL_CONFIG_CH_CONS_INFO(master_nasid)->memory_base +
- IOC3_BYTEBUS_DEV0);
- res.end = res.start + 32767;
- res.flags = IORESOURCE_MEM;
-
- return IS_ERR(platform_device_register_simple("rtc-m48t35", -1,
- &res, 1));
-}
-
-/*
- * kludge make this a device_initcall after ioc3 resource conflicts
- * are resolved
- */
-late_initcall(sgi_ip27_rtc_devinit);
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index ae24d3ea68ea..a762342065a2 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -2011,5 +2011,18 @@ config RAVE_SP_CORE
Select this to get support for the Supervisory Processor
device found on several devices in RAVE line of hardware.

+config SGI_MFD_IOC3
+ tristate "SGI IOC3 core driver"
+ depends on PCI && MIPS && 64BIT
+ select MFD_CORE
+ help
+ This option enables basic support for the SGI IOC3-based
+ controller cards. This option does not enable any specific
+ functions on such a card, but provides necessary infrastructure
+ for other drivers to utilize.
+
+ If you have an SGI Origin, Octane, or a PCI IOC3 card,
+ then say Y. Otherwise say N.
+
endmenu
endif
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index c1067ea46204..0d89b9e1055f 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -256,3 +256,4 @@ obj-$(CONFIG_MFD_ROHM_BD70528) += rohm-bd70528.o
obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o
obj-$(CONFIG_MFD_STMFX) += stmfx.o

+obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o
diff --git a/drivers/mfd/ioc3.c b/drivers/mfd/ioc3.c
new file mode 100644
index 000000000000..a63c7b1c4ad0
--- /dev/null
+++ b/drivers/mfd/ioc3.c
@@ -0,0 +1,588 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SGI IOC3 multifunction device driver
+ *
+ * Copyright (C) 2018, 2019 Thomas Bogendoerfer <tbogendoerfer@suse.de>
+ *
+ * Based on work by:
+ * Stanislaw Skowronek <skylark@unaligned.org>
+ * Joshua Kinard <kumba@gentoo.org>
+ * Brent Casavant <bcasavan@sgi.com> - IOC4 master driver
+ * Pat Gefre <pfg@sgi.com> - IOC3 serial port IRQ demuxer
+ */
+
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/sgi-w1.h>
+
+#include <asm/pci/bridge.h>
+#include <asm/sn/ioc3.h>
+
+#define IOC3_IRQ_SERIAL_A 6
+#define IOC3_IRQ_SERIAL_B 15
+#define IOC3_IRQ_KBD 22
+#define IOC3_IRQ_ETH_DOMAIN 23
+
+/* Bitmask for selecting which IRQs are level triggered */
+#define IOC3_LVL_MASK (BIT(IOC3_IRQ_SERIAL_A) | BIT(IOC3_IRQ_SERIAL_B))
+
+#define M48T35_REG_SIZE 32768 /* size of m48t35 registers */
+
+/* 1.2 us latency timer (40 cycles at 33 MHz) */
+#define IOC3_LATENCY 40
+
+struct ioc3_priv_data {
+ struct irq_domain *domain;
+ struct ioc3 __iomem *regs;
+ struct pci_dev *pdev;
+ int domain_irq;
+};
+
+static void ioc3_irq_ack(struct irq_data *d)
+{
+ struct ioc3_priv_data *ipd = irq_data_get_irq_chip_data(d);
+ unsigned int hwirq = irqd_to_hwirq(d);
+
+ writel(BIT(hwirq), &ipd->regs->sio_ir);
+}
+
+static void ioc3_irq_mask(struct irq_data *d)
+{
+ struct ioc3_priv_data *ipd = irq_data_get_irq_chip_data(d);
+ unsigned int hwirq = irqd_to_hwirq(d);
+
+ writel(BIT(hwirq), &ipd->regs->sio_iec);
+}
+
+static void ioc3_irq_unmask(struct irq_data *d)
+{
+ struct ioc3_priv_data *ipd = irq_data_get_irq_chip_data(d);
+ unsigned int hwirq = irqd_to_hwirq(d);
+
+ writel(BIT(hwirq), &ipd->regs->sio_ies);
+}
+
+static struct irq_chip ioc3_irq_chip = {
+ .name = "IOC3",
+ .irq_ack = ioc3_irq_ack,
+ .irq_mask = ioc3_irq_mask,
+ .irq_unmask = ioc3_irq_unmask,
+};
+
+static int ioc3_irq_domain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ /* Set level IRQs for every interrupt contained in IOC3_LVL_MASK */
+ if (BIT(hwirq) & IOC3_LVL_MASK)
+ irq_set_chip_and_handler(irq, &ioc3_irq_chip, handle_level_irq);
+ else
+ irq_set_chip_and_handler(irq, &ioc3_irq_chip, handle_edge_irq);
+
+ irq_set_chip_data(irq, d->host_data);
+ return 0;
+}
+
+static const struct irq_domain_ops ioc3_irq_domain_ops = {
+ .map = ioc3_irq_domain_map,
+};
+
+static void ioc3_irq_handler(struct irq_desc *desc)
+{
+ struct irq_domain *domain = irq_desc_get_handler_data(desc);
+ struct ioc3_priv_data *ipd = domain->host_data;
+ struct ioc3 __iomem *regs = ipd->regs;
+ u32 pending, mask;
+ unsigned int irq;
+
+ pending = readl(&regs->sio_ir);
+ mask = readl(&regs->sio_ies);
+ pending &= mask; /* Mask off not enabled interrupts */
+
+ if (mask & BIT(IOC3_IRQ_ETH_DOMAIN))
+ /*
+ * If ethernet interrupt is enabled we need to check
+ * ethernet registers for pending interrupts
+ */
+ if (readl(&regs->eth.eisr) & readl(&regs->eth.eier))
+ pending |= IOC3_IRQ_ETH_DOMAIN;
+
+ if (pending) {
+ irq = irq_find_mapping(domain, __ffs(pending));
+ if (irq)
+ generic_handle_irq(irq);
+ } else {
+ spurious_interrupt();
+ }
+}
+
+/*
+ * System boards/BaseIOs use more interrupt pins of the bridge ASIC
+ * to which the IOC3 is connected. Since the IOC3 MFD driver
+ * knows wiring of these extra pins, we use the map_irq function
+ * to get interrupts activated
+ */
+static int ioc3_map_irq(struct pci_dev *pdev, int pin)
+{
+ struct pci_host_bridge *hbrg = pci_find_host_bridge(pdev->bus);
+
+ return hbrg->map_irq(pdev, pin, 0);
+}
+
+static int ioc3_irq_domain_setup(struct ioc3_priv_data *ipd, int irq)
+{
+ struct irq_domain *domain;
+ struct fwnode_handle *fn;
+
+ fn = irq_domain_alloc_named_fwnode("IOC3");
+ if (!fn)
+ goto err;
+
+ domain = irq_domain_create_linear(fn, 24, &ioc3_irq_domain_ops, ipd);
+ if (!domain)
+ goto err;
+
+ irq_domain_free_fwnode(fn);
+ ipd->domain = domain;
+
+ irq_set_chained_handler_and_data(irq, ioc3_irq_handler, domain);
+ ipd->domain_irq = irq;
+ return 0;
+
+err:
+ dev_err(&ipd->pdev->dev, "irq domain setup failed\n");
+ return -ENOMEM;
+}
+
+static struct resource ioc3_uarta_resources[] = {
+ DEFINE_RES_MEM(offsetof(struct ioc3, sregs.uarta),
+ sizeof_field(struct ioc3, sregs.uarta)),
+ DEFINE_RES_IRQ(IOC3_IRQ_SERIAL_A)
+};
+
+static struct resource ioc3_uartb_resources[] = {
+ DEFINE_RES_MEM(offsetof(struct ioc3, sregs.uartb),
+ sizeof_field(struct ioc3, sregs.uartb)),
+ DEFINE_RES_IRQ(IOC3_IRQ_SERIAL_B)
+};
+
+static struct mfd_cell ioc3_serial_cells[] = {
+ {
+ .name = "ioc3-serial8250",
+ .resources = ioc3_uarta_resources,
+ .num_resources = ARRAY_SIZE(ioc3_uarta_resources),
+ },
+ {
+ .name = "ioc3-serial8250",
+ .resources = ioc3_uartb_resources,
+ .num_resources = ARRAY_SIZE(ioc3_uartb_resources),
+ }
+};
+
+static int ioc3_serial_setup(struct ioc3_priv_data *ipd)
+{
+ int ret;
+
+ /* Set gpio pins for RS232/RS422 mode selection */
+ writel(GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL,
+ &ipd->regs->gpcr_s);
+ /* Select RS232 mode for uart a */
+ writel(0, &ipd->regs->gppr[6]);
+ /* Select RS232 mode for uart b */
+ writel(0, &ipd->regs->gppr[7]);
+
+ /* Switch both ports to 16650 mode */
+ writel(readl(&ipd->regs->port_a.sscr) & ~SSCR_DMA_EN,
+ &ipd->regs->port_a.sscr);
+ writel(readl(&ipd->regs->port_b.sscr) & ~SSCR_DMA_EN,
+ &ipd->regs->port_b.sscr);
+ udelay(1000); /* Wait until mode switch is done */
+
+ ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO,
+ ioc3_serial_cells, ARRAY_SIZE(ioc3_serial_cells),
+ &ipd->pdev->resource[0], 0, ipd->domain);
+ if (ret) {
+ dev_err(&ipd->pdev->dev, "Failed to add 16550 subdevs\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct resource ioc3_kbd_resources[] = {
+ DEFINE_RES_MEM(offsetof(struct ioc3, serio),
+ sizeof_field(struct ioc3, serio)),
+ DEFINE_RES_IRQ(IOC3_IRQ_KBD)
+};
+
+static struct mfd_cell ioc3_kbd_cells[] = {
+ {
+ .name = "ioc3-kbd",
+ .resources = ioc3_kbd_resources,
+ .num_resources = ARRAY_SIZE(ioc3_kbd_resources),
+ }
+};
+
+static int ioc3_kbd_setup(struct ioc3_priv_data *ipd)
+{
+ int ret;
+
+ ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO,
+ ioc3_kbd_cells, ARRAY_SIZE(ioc3_kbd_cells),
+ &ipd->pdev->resource[0], 0, ipd->domain);
+ if (ret) {
+ dev_err(&ipd->pdev->dev, "Failed to add 16550 subdevs\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct resource ioc3_eth_resources[] = {
+ DEFINE_RES_MEM(offsetof(struct ioc3, eth),
+ sizeof_field(struct ioc3, eth)),
+ DEFINE_RES_MEM(offsetof(struct ioc3, ssram),
+ sizeof_field(struct ioc3, ssram)),
+ DEFINE_RES_IRQ(0)
+};
+
+static struct resource ioc3_w1_resources[] = {
+ DEFINE_RES_MEM(offsetof(struct ioc3, mcr),
+ sizeof_field(struct ioc3, mcr)),
+};
+static struct sgi_w1_platform_data ioc3_w1_platform_data;
+
+static struct mfd_cell ioc3_eth_cells[] = {
+ {
+ .name = "ioc3-eth",
+ .resources = ioc3_eth_resources,
+ .num_resources = ARRAY_SIZE(ioc3_eth_resources),
+ },
+ {
+ .name = "sgi_w1",
+ .resources = ioc3_w1_resources,
+ .num_resources = ARRAY_SIZE(ioc3_w1_resources),
+ .platform_data = &ioc3_w1_platform_data,
+ .pdata_size = sizeof(ioc3_w1_platform_data),
+ }
+};
+
+static int ioc3_eth_setup(struct ioc3_priv_data *ipd, bool use_domain)
+{
+ int irq = ipd->pdev->irq;
+ int ret;
+
+ /* Enable One-Wire bus */
+ writel(GPCR_MLAN_EN, &ipd->regs->gpcr_s);
+
+ /* Generate unique identifier */
+ snprintf(ioc3_w1_platform_data.dev_id,
+ sizeof(ioc3_w1_platform_data.dev_id), "ioc3-%012llx",
+ ipd->pdev->resource->start);
+
+ if (use_domain)
+ irq = irq_create_mapping(ipd->domain, IOC3_IRQ_ETH_DOMAIN);
+
+ ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO,
+ ioc3_eth_cells, ARRAY_SIZE(ioc3_eth_cells),
+ &ipd->pdev->resource[0], irq, NULL);
+ if (ret) {
+ dev_err(&ipd->pdev->dev, "Failed to add ETH/W1 subdev\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct resource ioc3_m48t35_resources[] = {
+ DEFINE_RES_MEM(IOC3_BYTEBUS_DEV0, M48T35_REG_SIZE)
+};
+
+static struct mfd_cell ioc3_m48t35_cells[] = {
+ {
+ .name = "rtc-m48t35",
+ .resources = ioc3_m48t35_resources,
+ .num_resources = ARRAY_SIZE(ioc3_m48t35_resources),
+ }
+};
+
+static int ioc3_m48t35_setup(struct ioc3_priv_data *ipd)
+{
+ int ret;
+
+ ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO,
+ ioc3_m48t35_cells, ARRAY_SIZE(ioc3_m48t35_cells),
+ &ipd->pdev->resource[0], 0, ipd->domain);
+ if (ret)
+ dev_err(&ipd->pdev->dev, "Failed to add M48T35 subdev\n");
+
+ return ret;
+}
+
+static int ip27_baseio_setup(struct ioc3_priv_data *ipd)
+{
+ int ret, io_irq;
+
+ io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 2);
+ ret = ioc3_irq_domain_setup(ipd, io_irq);
+ if (ret)
+ return ret;
+
+ ret = ioc3_eth_setup(ipd, false);
+ if (ret)
+ return ret;
+
+ ret = ioc3_serial_setup(ipd);
+ if (ret)
+ return ret;
+
+ return ioc3_m48t35_setup(ipd);
+}
+
+static int ip27_baseio6g_setup(struct ioc3_priv_data *ipd)
+{
+ int ret, io_irq;
+
+ io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 2);
+ ret = ioc3_irq_domain_setup(ipd, io_irq);
+ if (ret)
+ return ret;
+
+ ret = ioc3_eth_setup(ipd, false);
+ if (ret)
+ return ret;
+
+ ret = ioc3_serial_setup(ipd);
+ if (ret)
+ return ret;
+
+ ret = ioc3_m48t35_setup(ipd);
+ if (ret)
+ return ret;
+
+ return ioc3_kbd_setup(ipd);
+}
+
+static int ip27_mio_setup(struct ioc3_priv_data *ipd)
+{
+ int ret;
+
+ ret = ioc3_irq_domain_setup(ipd, ipd->pdev->irq);
+ if (ret)
+ return ret;
+
+ ret = ioc3_serial_setup(ipd);
+ if (ret)
+ return ret;
+
+ return ioc3_kbd_setup(ipd);
+}
+
+static int ip29_sysboard_setup(struct ioc3_priv_data *ipd)
+{
+ int ret, io_irq;
+
+ io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 1);
+ ret = ioc3_irq_domain_setup(ipd, io_irq);
+ if (ret)
+ return ret;
+
+ ret = ioc3_eth_setup(ipd, false);
+ if (ret)
+ return ret;
+
+ ret = ioc3_serial_setup(ipd);
+ if (ret)
+ return ret;
+
+ ret = ioc3_m48t35_setup(ipd);
+ if (ret)
+ return ret;
+
+ return ioc3_kbd_setup(ipd);
+}
+
+static int ioc3_menet_setup(struct ioc3_priv_data *ipd)
+{
+ int ret, io_irq;
+
+ io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 4);
+ ret = ioc3_irq_domain_setup(ipd, io_irq);
+ if (ret)
+ return ret;
+
+ ret = ioc3_eth_setup(ipd, false);
+ if (ret)
+ return ret;
+
+ return ioc3_serial_setup(ipd);
+}
+
+static int ioc3_menet4_setup(struct ioc3_priv_data *ipd)
+{
+ return ioc3_eth_setup(ipd, false);
+}
+
+static int ioc3_cad_duo_setup(struct ioc3_priv_data *ipd)
+{
+ int ret;
+
+ ret = ioc3_irq_domain_setup(ipd, ipd->pdev->irq);
+ if (ret)
+ return ret;
+
+ ret = ioc3_eth_setup(ipd, true);
+ if (ret)
+ return ret;
+
+ return ioc3_kbd_setup(ipd);
+}
+
+/* Helper macro for filling ioc3_info array */
+#define IOC3_SID(_name, _sid, _setup) \
+ { \
+ .name = _name, \
+ .sid = (PCI_VENDOR_ID_SGI << 16) | IOC3_SUBSYS_ ## _sid, \
+ .setup = _setup, \
+ }
+
+static struct {
+ const char *name;
+ u32 sid;
+ int (*setup)(struct ioc3_priv_data *ipd);
+} ioc3_infos[] = {
+ IOC3_SID("IP27 BaseIO6G", IP27_BASEIO6G, &ip27_baseio6g_setup),
+ IOC3_SID("IP27 MIO", IP27_MIO, &ip27_mio_setup),
+ IOC3_SID("IP27 BaseIO", IP27_BASEIO, &ip27_baseio_setup),
+ IOC3_SID("IP29 System Board", IP29_SYSBOARD, &ip29_sysboard_setup),
+ IOC3_SID("MENET", MENET, &ioc3_menet_setup),
+ IOC3_SID("MENET4", MENET4, &ioc3_menet4_setup)
+};
+#undef IOC3_SID
+
+static int ioc3_setup(struct ioc3_priv_data *ipd)
+{
+ u32 sid;
+ int i;
+
+ /* Clear IRQs */
+ writel(~0, &ipd->regs->sio_iec);
+ writel(~0, &ipd->regs->sio_ir);
+ writel(0, &ipd->regs->eth.eier);
+ writel(~0, &ipd->regs->eth.eisr);
+
+ /* Read subsystem vendor id and subsystem id */
+ pci_read_config_dword(ipd->pdev, PCI_SUBSYSTEM_VENDOR_ID, &sid);
+
+ for (i = 0; i < ARRAY_SIZE(ioc3_infos); i++)
+ if (sid == ioc3_infos[i].sid) {
+ pr_info("ioc3: %s\n", ioc3_infos[i].name);
+ return ioc3_infos[i].setup(ipd);
+ }
+
+ /* Treat everything not identified by PCI subid as CAD DUO */
+ pr_info("ioc3: CAD DUO\n");
+ return ioc3_cad_duo_setup(ipd);
+}
+
+static int ioc3_mfd_probe(struct pci_dev *pdev,
+ const struct pci_device_id *pci_id)
+{
+ struct ioc3_priv_data *ipd;
+ struct ioc3 __iomem *regs;
+ int ret;
+
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, IOC3_LATENCY);
+ pci_set_master(pdev);
+
+ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+ if (ret) {
+ dev_warn(&pdev->dev,
+ "Failed to set 64-bit DMA mask, trying 32-bit\n");
+ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+ if (ret) {
+ dev_err(&pdev->dev, "Can't set DMA mask, aborting\n");
+ return ret;
+ }
+ }
+
+ /* Set up per-IOC3 data */
+ ipd = devm_kzalloc(&pdev->dev, sizeof(struct ioc3_priv_data),
+ GFP_KERNEL);
+ if (!ipd) {
+ ret = -ENOMEM;
+ goto out_disable_device;
+ }
+ ipd->pdev = pdev;
+
+ /*
+ * Map all IOC3 registers. These are shared between subdevices
+ * so the main IOC3 module manages them.
+ */
+ regs = pci_ioremap_bar(pdev, 0);
+ if (!regs) {
+ dev_warn(&pdev->dev, "ioc3: Unable to remap PCI BAR for %s.\n",
+ pci_name(pdev));
+ ret = -ENOMEM;
+ goto out_disable_device;
+ }
+ ipd->regs = regs;
+
+ /* Track PCI-device specific data */
+ pci_set_drvdata(pdev, ipd);
+
+ ret = ioc3_setup(ipd);
+ if (ret)
+ goto out_disable_device;
+
+ return 0;
+
+out_disable_device:
+ pci_disable_device(pdev);
+ return ret;
+}
+
+static void ioc3_mfd_remove(struct pci_dev *pdev)
+{
+ struct ioc3_priv_data *ipd;
+
+ ipd = pci_get_drvdata(pdev);
+
+ /* Clear and disable all IRQs */
+ writel(~0, &ipd->regs->sio_iec);
+ writel(~0, &ipd->regs->sio_ir);
+
+ /* Release resources */
+ if (ipd->domain) {
+ irq_domain_remove(ipd->domain);
+ free_irq(ipd->domain_irq, (void *)ipd);
+ }
+ pci_disable_device(pdev);
+}
+
+static struct pci_device_id ioc3_mfd_id_table[] = {
+ { PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3, PCI_ANY_ID, PCI_ANY_ID },
+ { 0, },
+};
+MODULE_DEVICE_TABLE(pci, ioc3_mfd_id_table);
+
+static struct pci_driver ioc3_mfd_driver = {
+ .name = "IOC3",
+ .id_table = ioc3_mfd_id_table,
+ .probe = ioc3_mfd_probe,
+ .remove = ioc3_mfd_remove,
+};
+
+module_pci_driver(ioc3_mfd_driver);
+
+MODULE_AUTHOR("Thomas Bogendoerfer <tbogendoerfer@suse.de>");
+MODULE_DESCRIPTION("SGI IOC3 MFD driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/net/ethernet/sgi/Kconfig b/drivers/net/ethernet/sgi/Kconfig
index 37f048e1230c..bc26fa0d196f 100644
--- a/drivers/net/ethernet/sgi/Kconfig
+++ b/drivers/net/ethernet/sgi/Kconfig
@@ -6,7 +6,7 @@
config NET_VENDOR_SGI
bool "SGI devices"
default y
- depends on (PCI && SGI_IP27) || SGI_IP32
+ depends on (PCI && SGI_MFD_IOC3) || SGI_IP32
---help---
If you have a network (Ethernet) card belonging to this class, say Y.

@@ -19,7 +19,8 @@ if NET_VENDOR_SGI

config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on PCI && SGI_IP27
+ depends on PCI && SGI_MFD_IOC3
+ select CRC16
select CRC32
select MII
---help---
diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c
index deb636d653f3..9a86156acbdf 100644
--- a/drivers/net/ethernet/sgi/ioc3-eth.c
+++ b/drivers/net/ethernet/sgi/ioc3-eth.c
@@ -14,7 +14,6 @@
* o Use prefetching for large packets. What is a good lower limit for
* prefetching?
* o Use hardware checksums.
- * o Convert to using a IOC3 meta driver.
* o Which PHYs might possibly be attached to the IOC3 in real live,
* which workarounds are required for them? Do we ever have Lucent's?
* o For the 2.5 branch kill the mii-tool ioctls.
@@ -28,7 +27,8 @@
#include <linux/mm.h>
#include <linux/errno.h>
#include <linux/module.h>
-#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/crc16.h>
#include <linux/crc32.h>
#include <linux/mii.h>
#include <linux/in.h>
@@ -37,28 +37,22 @@
#include <linux/tcp.h>
#include <linux/udp.h>
#include <linux/gfp.h>
-
-#ifdef CONFIG_SERIAL_8250
-#include <linux/serial_core.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_reg.h>
-#endif
-
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/skbuff.h>
#include <linux/dma-direct.h>
+#include <linux/platform_device.h>
+#include <linux/nvmem-consumer.h>

#include <net/ip.h>

-#include <asm/byteorder.h>
-#include <asm/pgtable.h>
-#include <linux/uaccess.h>
-#include <asm/sn/types.h>
#include <asm/sn/ioc3.h>
#include <asm/pci/bridge.h>

+#define CRC16_INIT 0
+#define CRC16_VALID 0xb001
+
/* Number of RX buffers. This is tunable in the range of 16 <= x < 512.
* The value must be a power of two.
*/
@@ -85,7 +79,6 @@
/* Private per NIC data of the driver. */
struct ioc3_private {
struct ioc3_ethregs *regs;
- struct ioc3 *all_regs;
struct device *dma_dev;
u32 *ssram;
unsigned long *rxr; /* pointer to receiver ring */
@@ -103,9 +96,6 @@ struct ioc3_private {
spinlock_t ioc3_lock;
struct mii_if_info mii;

- struct net_device *dev;
- struct pci_dev *pdev;
-
/* Members used by autonegotiation */
struct timer_list ioc3_timer;
};
@@ -122,10 +112,8 @@ static int ioc3_alloc_rx_bufs(struct net_device *dev);
static void ioc3_free_rx_bufs(struct ioc3_private *ip);
static inline void ioc3_clean_tx_ring(struct ioc3_private *ip);

-static const char ioc3_str[] = "IOC3 Ethernet";
static const struct ethtool_ops ioc3_ethtool_ops;

-
static inline unsigned long aligned_rx_skb_addr(unsigned long addr)
{
return (~addr + 1) & (IOC3_DMA_XFER_LEN - 1UL);
@@ -178,225 +166,61 @@ static inline unsigned long ioc3_map(dma_addr_t addr, unsigned long attr)
#define ERBAR_VAL 0
#endif

-#define IOC3_SIZE 0x100000
-
-static inline u32 mcr_pack(u32 pulse, u32 sample)
-{
- return (pulse << 10) | (sample << 2);
-}
-
-static int nic_wait(u32 __iomem *mcr)
-{
- u32 m;
-
- do {
- m = readl(mcr);
- } while (!(m & 2));
-
- return m & 1;
-}
-
-static int nic_reset(u32 __iomem *mcr)
-{
- int presence;
-
- writel(mcr_pack(500, 65), mcr);
- presence = nic_wait(mcr);
-
- writel(mcr_pack(0, 500), mcr);
- nic_wait(mcr);
-
- return presence;
-}
-
-static inline int nic_read_bit(u32 __iomem *mcr)
-{
- int result;
-
- writel(mcr_pack(6, 13), mcr);
- result = nic_wait(mcr);
- writel(mcr_pack(0, 100), mcr);
- nic_wait(mcr);
-
- return result;
-}
-
-static inline void nic_write_bit(u32 __iomem *mcr, int bit)
-{
- if (bit)
- writel(mcr_pack(6, 110), mcr);
- else
- writel(mcr_pack(80, 30), mcr);
-
- nic_wait(mcr);
-}
-
-/* Read a byte from an iButton device
- */
-static u32 nic_read_byte(u32 __iomem *mcr)
-{
- u32 result = 0;
- int i;
-
- for (i = 0; i < 8; i++)
- result = (result >> 1) | (nic_read_bit(mcr) << 7);
-
- return result;
-}
-
-/* Write a byte to an iButton device
- */
-static void nic_write_byte(u32 __iomem *mcr, int byte)
+static int ioc3eth_nvmem_match(struct device *dev, const void *data)
{
- int i, bit;
-
- for (i = 8; i; i--) {
- bit = byte & 1;
- byte >>= 1;
-
- nic_write_bit(mcr, bit);
- }
-}
+ const char *name = dev_name(dev);
+ const char *prefix = data;
+ int prefix_len;

-static u64 nic_find(u32 __iomem *mcr, int *last)
-{
- int a, b, index, disc;
- u64 address = 0;
-
- nic_reset(mcr);
- /* Search ROM. */
- nic_write_byte(mcr, 0xf0);
-
- /* Algorithm from ``Book of iButton Standards''. */
- for (index = 0, disc = 0; index < 64; index++) {
- a = nic_read_bit(mcr);
- b = nic_read_bit(mcr);
-
- if (a && b) {
- pr_warn("NIC search failed (not fatal).\n");
- *last = 0;
- return 0;
- }
+ prefix_len = strlen(prefix);
+ if (strlen(name) < (prefix_len + 3))
+ return 0;

- if (!a && !b) {
- if (index == *last) {
- address |= 1UL << index;
- } else if (index > *last) {
- address &= ~(1UL << index);
- disc = index;
- } else if ((address & (1UL << index)) == 0) {
- disc = index;
- }
- nic_write_bit(mcr, address & (1UL << index));
- continue;
- } else {
- if (a)
- address |= 1UL << index;
- else
- address &= ~(1UL << index);
- nic_write_bit(mcr, a);
- continue;
- }
- }
-
- *last = disc;
-
- return address;
-}
-
-static int nic_init(u32 __iomem *mcr)
-{
- const char *unknown = "unknown";
- const char *type = unknown;
- u8 crc;
- u8 serial[6];
- int save = 0, i;
-
- while (1) {
- u64 reg;
-
- reg = nic_find(mcr, &save);
-
- switch (reg & 0xff) {
- case 0x91:
- type = "DS1981U";
- break;
- default:
- if (save == 0) {
- /* Let the caller try again. */
- return -1;
- }
- continue;
- }
+ if (memcmp(prefix, name, prefix_len) != 0)
+ return 0;

- nic_reset(mcr);
-
- /* Match ROM. */
- nic_write_byte(mcr, 0x55);
- for (i = 0; i < 8; i++)
- nic_write_byte(mcr, (reg >> (i << 3)) & 0xff);
-
- reg >>= 8; /* Shift out type. */
- for (i = 0; i < 6; i++) {
- serial[i] = reg & 0xff;
- reg >>= 8;
- }
- crc = reg & 0xff;
- break;
- }
-
- pr_info("Found %s NIC", type);
- if (type != unknown)
- pr_cont(" registration number %pM, CRC %02x", serial, crc);
- pr_cont(".\n");
+ /* found nvmem device which is attached to our ioc3
+ * now check for one wire family code 09, 89 and 91
+ */
+ if (memcmp(name + prefix_len, "09-", 3) == 0)
+ return 1;
+ if (memcmp(name + prefix_len, "89-", 3) == 0)
+ return 1;
+ if (memcmp(name + prefix_len, "91-", 3) == 0)
+ return 1;

return 0;
}

-/* Read the NIC (Number-In-a-Can) device used to store the MAC address on
- * SN0 / SN00 nodeboards and PCI cards.
- */
-static void ioc3_get_eaddr_nic(struct ioc3_private *ip)
+static int ioc3eth_get_mac_addr(struct resource *res, u8 mac_addr[6])
{
- u32 __iomem *mcr = &ip->all_regs->mcr;
- int tries = 2; /* There may be some problem with the battery? */
- u8 nic[14];
+ struct nvmem_device *nvmem;
+ char prefix[24];
+ u8 prom[16];
+ int ret;
int i;

- writel(1 << 21, &ip->all_regs->gpcr_s);
-
- while (tries--) {
- if (!nic_init(mcr))
- break;
- udelay(500);
- }
-
- if (tries < 0) {
- pr_err("Failed to read MAC address\n");
- return;
- }
+ snprintf(prefix, sizeof(prefix), "ioc3-%012llx-",
+ res->start & ~0xffff);

- /* Read Memory. */
- nic_write_byte(mcr, 0xf0);
- nic_write_byte(mcr, 0x00);
- nic_write_byte(mcr, 0x00);
+ nvmem = nvmem_device_find(prefix, ioc3eth_nvmem_match);
+ if (IS_ERR(nvmem))
+ return PTR_ERR(nvmem);

- for (i = 13; i >= 0; i--)
- nic[i] = nic_read_byte(mcr);
+ ret = nvmem_device_read(nvmem, 0, 16, prom);
+ nvmem_device_put(nvmem);
+ if (ret < 0)
+ return ret;

- for (i = 2; i < 8; i++)
- ip->dev->dev_addr[i - 2] = nic[i];
-}
+ /* check, if content is valid */
+ if (prom[0] != 0x0a ||
+ crc16(CRC16_INIT, prom, 13) != CRC16_VALID)
+ return -EINVAL;

-/* Ok, this is hosed by design. It's necessary to know what machine the
- * NIC is in in order to know how to read the NIC address. We also have
- * to know if it's a PCI card or a NIC in on the node board ...
- */
-static void ioc3_get_eaddr(struct ioc3_private *ip)
-{
- ioc3_get_eaddr_nic(ip);
+ for (i = 0; i < 6; i++)
+ mac_addr[i] = prom[10 - i];

- pr_info("Ethernet address is %pM.\n", ip->dev->dev_addr);
+ return 0;
}

static void __ioc3_set_mac_address(struct net_device *dev)
@@ -769,7 +593,7 @@ static int ioc3_mii_init(struct ioc3_private *ip)
u16 word;

for (i = 0; i < 32; i++) {
- word = ioc3_mdio_read(ip->dev, i, MII_PHYSID1);
+ word = ioc3_mdio_read(ip->mii.dev, i, MII_PHYSID1);

if (word != 0xffff && word != 0x0000) {
found = 1;
@@ -974,12 +798,6 @@ static int ioc3_open(struct net_device *dev)
{
struct ioc3_private *ip = netdev_priv(dev);

- if (request_irq(dev->irq, ioc3_interrupt, IRQF_SHARED, ioc3_str, dev)) {
- netdev_err(dev, "Can't get irq %d\n", dev->irq);
-
- return -EAGAIN;
- }
-
ip->ehar_h = 0;
ip->ehar_l = 0;

@@ -1012,147 +830,6 @@ static int ioc3_close(struct net_device *dev)
return 0;
}

-/* MENET cards have four IOC3 chips, which are attached to two sets of
- * PCI slot resources each: the primary connections are on slots
- * 0..3 and the secondaries are on 4..7
- *
- * All four ethernets are brought out to connectors; six serial ports
- * (a pair from each of the first three IOC3s) are brought out to
- * MiniDINs; all other subdevices are left swinging in the wind, leave
- * them disabled.
- */
-
-static int ioc3_adjacent_is_ioc3(struct pci_dev *pdev, int slot)
-{
- struct pci_dev *dev = pci_get_slot(pdev->bus, PCI_DEVFN(slot, 0));
- int ret = 0;
-
- if (dev) {
- if (dev->vendor == PCI_VENDOR_ID_SGI &&
- dev->device == PCI_DEVICE_ID_SGI_IOC3)
- ret = 1;
- pci_dev_put(dev);
- }
-
- return ret;
-}
-
-static int ioc3_is_menet(struct pci_dev *pdev)
-{
- return !pdev->bus->parent &&
- ioc3_adjacent_is_ioc3(pdev, 0) &&
- ioc3_adjacent_is_ioc3(pdev, 1) &&
- ioc3_adjacent_is_ioc3(pdev, 2);
-}
-
-#ifdef CONFIG_SERIAL_8250
-/* Note about serial ports and consoles:
- * For console output, everyone uses the IOC3 UARTA (offset 0x178)
- * connected to the master node (look in ip27_setup_console() and
- * ip27prom_console_write()).
- *
- * For serial (/dev/ttyS0 etc), we can not have hardcoded serial port
- * addresses on a partitioned machine. Since we currently use the ioc3
- * serial ports, we use dynamic serial port discovery that the serial.c
- * driver uses for pci/pnp ports (there is an entry for the SGI ioc3
- * boards in pci_boards[]). Unfortunately, UARTA's pio address is greater
- * than UARTB's, although UARTA on o200s has traditionally been known as
- * port 0. So, we just use one serial port from each ioc3 (since the
- * serial driver adds addresses to get to higher ports).
- *
- * The first one to do a register_console becomes the preferred console
- * (if there is no kernel command line console= directive). /dev/console
- * (ie 5, 1) is then "aliased" into the device number returned by the
- * "device" routine referred to in this console structure
- * (ip27prom_console_dev).
- *
- * Also look in ip27-pci.c:pci_fixup_ioc3() for some comments on working
- * around ioc3 oddities in this respect.
- *
- * The IOC3 serials use a 22MHz clock rate with an additional divider which
- * can be programmed in the SCR register if the DLAB bit is set.
- *
- * Register to interrupt zero because we share the interrupt with
- * the serial driver which we don't properly support yet.
- *
- * Can't use UPF_IOREMAP as the whole of IOC3 resources have already been
- * registered.
- */
-static void ioc3_8250_register(struct ioc3_uartregs __iomem *uart)
-{
-#define COSMISC_CONSTANT 6
-
- struct uart_8250_port port = {
- .port = {
- .irq = 0,
- .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
- .iotype = UPIO_MEM,
- .regshift = 0,
- .uartclk = (22000000 << 1) / COSMISC_CONSTANT,
-
- .membase = (unsigned char __iomem *)uart,
- .mapbase = (unsigned long)uart,
- }
- };
- unsigned char lcr;
-
- lcr = readb(&uart->iu_lcr);
- writeb(lcr | UART_LCR_DLAB, &uart->iu_lcr);
- writeb(COSMISC_CONSTANT, &uart->iu_scr);
- writeb(lcr, &uart->iu_lcr);
- readb(&uart->iu_lcr);
- serial8250_register_8250_port(&port);
-}
-
-static void ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
-{
- u32 sio_iec;
-
- /* We need to recognice and treat the fourth MENET serial as it
- * does not have an SuperIO chip attached to it, therefore attempting
- * to access it will result in bus errors. We call something an
- * MENET if PCI slot 0, 1, 2 and 3 of a master PCI bus all have an IOC3
- * in it. This is paranoid but we want to avoid blowing up on a
- * showhorn PCI box that happens to have 4 IOC3 cards in it so it's
- * not paranoid enough ...
- */
- if (ioc3_is_menet(pdev) && PCI_SLOT(pdev->devfn) == 3)
- return;
-
- /* Switch IOC3 to PIO mode. It probably already was but let's be
- * paranoid
- */
- writel(GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL, &ioc3->gpcr_s);
- readl(&ioc3->gpcr_s);
- writel(0, &ioc3->gppr[6]);
- readl(&ioc3->gppr[6]);
- writel(0, &ioc3->gppr[7]);
- readl(&ioc3->gppr[7]);
- writel(readl(&ioc3->port_a.sscr) & ~SSCR_DMA_EN, &ioc3->port_a.sscr);
- readl(&ioc3->port_a.sscr);
- writel(readl(&ioc3->port_b.sscr) & ~SSCR_DMA_EN, &ioc3->port_b.sscr);
- readl(&ioc3->port_b.sscr);
- /* Disable all SA/B interrupts except for SA/B_INT in SIO_IEC. */
- sio_iec = readl(&ioc3->sio_iec);
- sio_iec &= ~(SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL |
- SIO_IR_SA_RX_HIGH | SIO_IR_SA_RX_TIMER |
- SIO_IR_SA_DELTA_DCD | SIO_IR_SA_DELTA_CTS |
- SIO_IR_SA_TX_EXPLICIT | SIO_IR_SA_MEMERR);
- sio_iec |= SIO_IR_SA_INT;
- sio_iec &= ~(SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL |
- SIO_IR_SB_RX_HIGH | SIO_IR_SB_RX_TIMER |
- SIO_IR_SB_DELTA_DCD | SIO_IR_SB_DELTA_CTS |
- SIO_IR_SB_TX_EXPLICIT | SIO_IR_SB_MEMERR);
- sio_iec |= SIO_IR_SB_INT;
- writel(sio_iec, &ioc3->sio_iec);
- writel(0, &ioc3->port_a.sscr);
- writel(0, &ioc3->port_b.sscr);
-
- ioc3_8250_register(&ioc3->sregs.uarta);
- ioc3_8250_register(&ioc3->sregs.uartb);
-}
-#endif
-
static const struct net_device_ops ioc3_netdev_ops = {
.ndo_open = ioc3_open,
.ndo_stop = ioc3_close,
@@ -1165,76 +842,52 @@ static const struct net_device_ops ioc3_netdev_ops = {
.ndo_set_mac_address = ioc3_set_mac_address,
};

-static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+static int ioc3eth_probe(struct platform_device *pdev)
{
- unsigned int sw_physid1, sw_physid2;
- struct net_device *dev = NULL;
+ u32 sw_physid1, sw_physid2, vendor, model, rev;
struct ioc3_private *ip;
- struct ioc3 *ioc3;
- unsigned long ioc3_base, ioc3_size;
- u32 vendor, model, rev;
- int err, pci_using_dac;
-
- /* Configure DMA attributes. */
- err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
- if (!err) {
- pci_using_dac = 1;
- err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
- if (err < 0) {
- pr_err("%s: Unable to obtain 64 bit DMA for consistent allocations\n",
- pci_name(pdev));
- goto out;
- }
- } else {
- err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
- if (err) {
- pr_err("%s: No usable DMA configuration, aborting.\n",
- pci_name(pdev));
- goto out;
- }
- pci_using_dac = 0;
- }
+ struct net_device *dev;
+ struct resource *regs;
+ u8 mac_addr[6];
+ int err;

- if (pci_enable_device(pdev))
- return -ENODEV;
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ /* get mac addr from one wire prom */
+ if (ioc3eth_get_mac_addr(regs, mac_addr))
+ return -EPROBE_DEFER; /* not available yet */

dev = alloc_etherdev(sizeof(struct ioc3_private));
- if (!dev) {
- err = -ENOMEM;
- goto out_disable;
- }
-
- if (pci_using_dac)
- dev->features |= NETIF_F_HIGHDMA;
-
- err = pci_request_regions(pdev, "ioc3");
- if (err)
- goto out_free;
+ if (!dev)
+ return -ENOMEM;

SET_NETDEV_DEV(dev, &pdev->dev);

ip = netdev_priv(dev);
- ip->dev = dev;
- ip->dma_dev = &pdev->dev;
-
- dev->irq = pdev->irq;
+ ip->dma_dev = pdev->dev.parent;
+ ip->regs = devm_platform_ioremap_resource(pdev, 0);
+ if (!ip->regs) {
+ err = -ENOMEM;
+ goto out_free;
+ }

- ioc3_base = pci_resource_start(pdev, 0);
- ioc3_size = pci_resource_len(pdev, 0);
- ioc3 = (struct ioc3 *)ioremap(ioc3_base, ioc3_size);
- if (!ioc3) {
- pr_err("ioc3eth(%s): ioremap failed, goodbye.\n",
- pci_name(pdev));
+ ip->ssram = devm_platform_ioremap_resource(pdev, 1);
+ if (!ip->ssram) {
err = -ENOMEM;
- goto out_res;
+ goto out_free;
}
- ip->regs = &ioc3->eth;
- ip->ssram = ioc3->ssram;
- ip->all_regs = ioc3;

-#ifdef CONFIG_SERIAL_8250
- ioc3_serial_probe(pdev, ioc3);
-#endif
+ dev->irq = platform_get_irq(pdev, 0);
+ if (dev->irq < 0) {
+ err = dev->irq;
+ goto out_free;
+ }
+
+ if (devm_request_irq(&pdev->dev, dev->irq, ioc3_interrupt,
+ IRQF_SHARED, "ioc3-eth", dev)) {
+ dev_err(&pdev->dev, "Can't get irq %d\n", dev->irq);
+ err = -ENODEV;
+ goto out_free;
+ }

spin_lock_init(&ip->ioc3_lock);
timer_setup(&ip->ioc3_timer, ioc3_timer, 0);
@@ -1262,8 +915,6 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)

ioc3_init(dev);

- ip->pdev = pdev;
-
ip->mii.phy_id_mask = 0x1f;
ip->mii.reg_num_mask = 0x1f;
ip->mii.dev = dev;
@@ -1273,15 +924,14 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
ioc3_mii_init(ip);

if (ip->mii.phy_id == -1) {
- pr_err("ioc3-eth(%s): Didn't find a PHY, goodbye.\n",
- pci_name(pdev));
+ netdev_err(dev, "Didn't find a PHY, goodbye.\n");
err = -ENODEV;
goto out_stop;
}

ioc3_mii_start(ip);
ioc3_ssram_disc(ip);
- ioc3_get_eaddr(ip);
+ memcpy(dev->dev_addr, mac_addr, ETH_ALEN);

/* The IOC3-specific entries in the device structure. */
dev->watchdog_timeo = 5 * HZ;
@@ -1318,21 +968,14 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
if (ip->txr)
dma_direct_free_pages(ip->dma_dev, TX_RING_SIZE, ip->txr,
ip->txr_dma, 0);
-out_res:
- pci_release_regions(pdev);
out_free:
free_netdev(dev);
-out_disable:
- /* We should call pci_disable_device(pdev); here if the IOC3 wasn't
- * such a weird device ...
- */
-out:
return err;
}

-static void ioc3_remove_one(struct pci_dev *pdev)
+static int ioc3eth_remove(struct platform_device *pdev)
{
- struct net_device *dev = pci_get_drvdata(pdev);
+ struct net_device *dev = platform_get_drvdata(pdev);
struct ioc3_private *ip = netdev_priv(dev);

dma_direct_free_pages(ip->dma_dev, RX_RING_SIZE, ip->rxr,
@@ -1342,27 +985,11 @@ static void ioc3_remove_one(struct pci_dev *pdev)

unregister_netdev(dev);
del_timer_sync(&ip->ioc3_timer);
-
- iounmap(ip->all_regs);
- pci_release_regions(pdev);
free_netdev(dev);
- /* We should call pci_disable_device(pdev); here if the IOC3 wasn't
- * such a weird device ...
- */
-}

-static const struct pci_device_id ioc3_pci_tbl[] = {
- { PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3, PCI_ANY_ID, PCI_ANY_ID },
- { 0 }
-};
-MODULE_DEVICE_TABLE(pci, ioc3_pci_tbl);
+ return 0;
+}

-static struct pci_driver ioc3_driver = {
- .name = "ioc3-eth",
- .id_table = ioc3_pci_tbl,
- .probe = ioc3_probe,
- .remove = ioc3_remove_one,
-};

static netdev_tx_t ioc3_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
@@ -1544,11 +1171,10 @@ static inline unsigned int ioc3_hash(const unsigned char *addr)
static void ioc3_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
- struct ioc3_private *ip = netdev_priv(dev);
-
strlcpy(info->driver, IOC3_NAME, sizeof(info->driver));
strlcpy(info->version, IOC3_VERSION, sizeof(info->version));
- strlcpy(info->bus_info, pci_name(ip->pdev), sizeof(info->bus_info));
+ strlcpy(info->bus_info, pci_name(to_pci_dev(dev->dev.parent)),
+ sizeof(info->bus_info));
}

static int ioc3_get_link_ksettings(struct net_device *dev,
@@ -1660,7 +1286,16 @@ static void ioc3_set_multicast_list(struct net_device *dev)
spin_unlock_irq(&ip->ioc3_lock);
}

-module_pci_driver(ioc3_driver);
+static struct platform_driver ioc3eth_driver = {
+ .probe = ioc3eth_probe,
+ .remove = ioc3eth_remove,
+ .driver = {
+ .name = "ioc3-eth",
+ }
+};
+
+module_platform_driver(ioc3eth_driver);
+
MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
MODULE_DESCRIPTION("SGI IOC3 Ethernet driver");
MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_ioc3.c b/drivers/tty/serial/8250/8250_ioc3.c
new file mode 100644
index 000000000000..2be6ed2967e0
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_ioc3.c
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SGI IOC3 8250 UART driver
+ *
+ * Copyright (C) 2019 Thomas Bogendoerfer <tbogendoerfer@suse.de>
+ *
+ * based on code Copyright (C) 2005 Stanislaw Skowronek <skylark@unaligned.org>
+ * Copyright (C) 2014 Joshua Kinard <kumba@gentoo.org>
+ */
+
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+
+#include "8250.h"
+
+#define IOC3_UARTCLK (22000000 / 3)
+
+struct ioc3_8250_data {
+ int line;
+};
+
+static unsigned int ioc3_serial_in(struct uart_port *p, int offset)
+{
+ return readb(p->membase + offset);
+}
+
+static void ioc3_serial_out(struct uart_port *p, int offset, int value)
+{
+ writeb(value, p->membase + offset);
+}
+
+static int serial8250_ioc3_probe(struct platform_device *pdev)
+{
+ struct ioc3_8250_data *data;
+ struct uart_8250_port up;
+ struct resource *r;
+ void __iomem *membase;
+ int irq, line;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r)
+ return -ENODEV;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ membase = devm_ioremap_nocache(&pdev->dev, r->start, resource_size(r));
+ if (!membase)
+ return -ENOMEM;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ irq = 0; /* no interrupt -> use polling */
+
+ /* Register serial ports with 8250.c */
+ memset(&up, 0, sizeof(struct uart_8250_port));
+ up.port.iotype = UPIO_MEM;
+ up.port.uartclk = IOC3_UARTCLK;
+ up.port.type = PORT_16550A;
+ up.port.irq = irq;
+ up.port.flags = (UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ);
+ up.port.dev = &pdev->dev;
+ up.port.membase = membase;
+ up.port.mapbase = r->start;
+ up.port.serial_in = ioc3_serial_in;
+ up.port.serial_out = ioc3_serial_out;
+ line = serial8250_register_8250_port(&up);
+ if (line < 0)
+ return line;
+
+ platform_set_drvdata(pdev, data);
+ return 0;
+}
+
+static int serial8250_ioc3_remove(struct platform_device *pdev)
+{
+ struct ioc3_8250_data *data = platform_get_drvdata(pdev);
+
+ serial8250_unregister_port(data->line);
+ return 0;
+}
+
+static struct platform_driver serial8250_ioc3_driver = {
+ .probe = serial8250_ioc3_probe,
+ .remove = serial8250_ioc3_remove,
+ .driver = {
+ .name = "ioc3-serial8250",
+ }
+};
+
+module_platform_driver(serial8250_ioc3_driver);
+
+MODULE_AUTHOR("Thomas Bogendoerfer <tbogendoerfer@suse.de>");
+MODULE_DESCRIPTION("SGI IOC3 8250 UART driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 7ef60f8b6e2c..536808506545 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -370,6 +370,17 @@ config SERIAL_8250_EM
port hardware found on the Emma Mobile line of processors.
If unsure, say N.

+config SERIAL_8250_IOC3
+ tristate "SGI IOC3 8250 UART support"
+ depends on SGI_MFD_IOC3 && SERIAL_8250
+ select SERIAL_8250_EXTENDED
+ select SERIAL_8250_SHARE_IRQ
+ help
+ Enable this if you have a SGI Origin or Octane machine. This module
+ provides basic serial support by directly driving the UART chip
+ behind the IOC3 device on those systems. Maximum baud speed is
+ 38400bps using this driver.
+
config SERIAL_8250_RT288X
bool "Ralink RT288x/RT305x/RT3662/RT3883 serial port support"
depends on SERIAL_8250
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 08c1d8117506..51a6079d3f1f 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SERIAL_8250_FSL) += 8250_fsl.o
obj-$(CONFIG_SERIAL_8250_MEN_MCB) += 8250_men_mcb.o
obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o
obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
+obj-$(CONFIG_SERIAL_8250_IOC3) += 8250_ioc3.o
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
--
2.16.4
\
 
 \ /
  Last update: 2019-10-09 12:18    [W:0.081 / U:5.660 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site