lkml.org 
[lkml]   [2019]   [Oct]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] devfreq: exynos-bus: workaround dev_pm_opp_set_rate() errors on Exynos5422/5800 SoCs
From
Date
On 2019년 10월 08일 22:49, k.konieczny@partner.samsung.com wrote:
> Commit 4294a779bd8d ("PM / devfreq: exynos-bus: Convert to use
> dev_pm_opp_set_rate()") introduced errors:
> exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
> exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
> exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz)
> ...
> exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34)
> exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34)
> exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34)
>
> They are caused by incorrect PLL assigned to clock source, which results
> in clock rate outside of OPP range. Add workaround for this in
> exynos_bus_parse_of() by adjusting clock rate to those present in OPP.

If the clock caused this issue, you can set the initial clock on DeviceTree
with assigned-clock-* properties. Because the probe time of clock driver
is early than the any device drivers.

It is not proper to fix the clock issue on other device driver.
I think you can fix it by using the supported clock properties.


>
> Fixes: 4294a779bd8d ("PM / devfreq: exynos-bus: Convert to use dev_pm_opp_set_rate()")
> Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
> Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
> ---
> drivers/devfreq/exynos-bus.c | 14 +++++++++++---
> 1 file changed, 11 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c
> index c832673273a2..37bd34d5625b 100644
> --- a/drivers/devfreq/exynos-bus.c
> +++ b/drivers/devfreq/exynos-bus.c
> @@ -243,7 +243,7 @@ static int exynos_bus_parse_of(struct device_node *np,
> {
> struct device *dev = bus->dev;
> struct dev_pm_opp *opp;
> - unsigned long rate;
> + unsigned long rate, opp_rate;
> int ret;
>
> /* Get the clock to provide each bus with source clock */
> @@ -267,13 +267,21 @@ static int exynos_bus_parse_of(struct device_node *np,
> }
>
> rate = clk_get_rate(bus->clk);
> -
> - opp = devfreq_recommended_opp(dev, &rate, 0);
> + opp_rate = rate;
> + opp = devfreq_recommended_opp(dev, &opp_rate, 0);
> if (IS_ERR(opp)) {
> dev_err(dev, "failed to find dev_pm_opp\n");
> ret = PTR_ERR(opp);
> goto err_opp;
> }
> + /*
> + * FIXME: U-boot leaves clock source at incorrect PLL, this results
> + * in clock rate outside defined OPP rate. Work around this bug by
> + * setting clock rate to recommended one.
> + */
> + if (rate > opp_rate)
> + clk_set_rate(bus->clk, opp_rate);
> +
> bus->curr_freq = dev_pm_opp_get_freq(opp);
> dev_pm_opp_put(opp);
>
>


--
Best Regards,
Chanwoo Choi
Samsung Electronics

\
 
 \ /
  Last update: 2019-10-10 04:46    [W:0.027 / U:4.820 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site