lkml.org 
[lkml]   [2019]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] pwm: cros-ec: Let cros_ec_pwm_get_state() return the last applied state
On Tue, Oct 08, 2019 at 06:33:15PM +0200, Enric Balletbo i Serra wrote:
> Hi Uwe,
>
> Thanks for the quick reply.
>
> On 8/10/19 16:34, Uwe Kleine-König wrote:
> > Hello Enric,
> >
> > On Tue, Oct 08, 2019 at 12:54:17PM +0200, Enric Balletbo i Serra wrote:
> >> @@ -117,17 +122,28 @@ static void cros_ec_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> >> struct cros_ec_pwm_device *ec_pwm = pwm_to_cros_ec_pwm(chip);
> >> int ret;
> >>
> >> - ret = cros_ec_pwm_get_duty(ec_pwm->ec, pwm->hwpwm);
> >> - if (ret < 0) {
> >> - dev_err(chip->dev, "error getting initial duty: %d\n", ret);
> >> - return;
> >> + /*
> >> + * As there is no way for this hardware to separate the concept of
> >> + * duty cycle and enabled, but the PWM API does, let return the last
> >> + * applied state when the PWM is disabled and only return the real
> >> + * hardware value when the PWM is enabled. Otherwise, a user of this
> >> + * driver, can get confused because won't be able to program a duty
> >> + * cycle while the PWM is disabled.
> >> + */
> >> + state->enabled = ec_pwm->state.enabled;
> >
> >> + if (state->enabled) {
> >
> > As part of registration of the pwm .get_state is called. In this case
> > .apply wasn't called before and so state->enabled is probably 0. So this
> > breaks reporting the initial state ...
> >
> >> + ret = cros_ec_pwm_get_duty(ec_pwm->ec, pwm->hwpwm);
> >> + if (ret < 0) {
> >> + dev_err(chip->dev, "error getting initial duty: %d\n",
> >> + ret);
> >> + return;
> >> + }
> >> + state->duty_cycle = ret;
> >> + } else {
> >> + state->duty_cycle = ec_pwm->state.duty_cycle;
> >> }
> >>
> >> - state->enabled = (ret > 0);
> >> state->period = EC_PWM_MAX_DUTY;
> >> -
> >> - /* Note that "disabled" and "duty cycle == 0" are treated the same */
> >> - state->duty_cycle = ret;
> >
> > A few thoughts to your approach here ...:
> >
> > - Would it make sense to only store duty_cycle and enabled in the
> > driver struct?
> >
>
> Yes, in fact, my first approach (that I didn't send) was only storing enabled
> and duty cycle. For some reason I ended storing the full pwm_state struct, but I
> guess is not really needed.
>
>
> > - Which driver is the consumer of your pwm? If I understand correctly
> > the following sequence is the bad one:
> >
>
> The consumer is the pwm_bl driver. Actually I'n trying to identify
> other consumers.

Ah, I see why I missed to identify the problem back when I checked this
driver. The problem is not that .duty_cycle isn't set but there .enabled
isn't set. So maybe we just want:

diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
index 2201b8c78641..0468c6ee4448 100644
--- a/drivers/video/backlight/pwm_bl.c
+++ b/drivers/video/backlight/pwm_bl.c
@@ -123,6 +123,7 @@ static int pwm_backlight_update_status(struct backlight_device *bl)
if (brightness > 0) {
pwm_get_state(pb->pwm, &state);
state.duty_cycle = compute_duty_cycle(pb, brightness);
+ state.enabled = true;
pwm_apply_state(pb->pwm, &state);
pwm_backlight_power_on(pb);
} else
? On a side note: It's IMHO strange that pwm_backlight_power_on
reconfigures the PWM once more.

> > state.period = P;
> > state.duty_cycle = D;
> > state.enabled = 0;
> > pwm_apply_state(pwm, &state);
> >
> > ...
> >
> > pwm_get_state(pwm, &state);
> > state.enabled = 1;
> > pwm_apply_state(pwm, &state);
> >
>
> Yes that's the sequence.
>
> > Before my patch there was an implicit promise in the PWM framework
> > that the last pwm_apply_state has .duty_cycle = D (and .period = P).
> > Is this worthwile, or should we instead declare this as
> > non-guaranteed and fix the caller?
> >
>
> pwm_bl is compliant with this, the problem in the pwm-cros-ec driver is when you
> set the duty_cycle but enable is 0.

pwm_bl *relies* on this behaviour. The question is: Is this a valid
assumption to rely on (for consumers) resp. to guarantee (for the PWM
framework)? I'm not sure it is because each PWM that doesn't know the
concept of "disabled" (not sure how many there are) needs some effort to
simulate it (by caching duty_cycle and period on disable).

Dropping this promise and fix pwm_bl (and maybe other consumers that
rely on it) is my preferred solution.

> > - If this is a more or less common property that hardware doesn't know
> > the concept of "disabled" maybe it would make sense to drop this from
> > the PWM framework, too. (This is a question that I discussed some
> > time ago already with Thierry, but without an result. The key
> > question is: What is the difference between "disabled" and
> > "duty_cycle = 0" in general and does any consumer care about it.)
> >
>
> Good question, I don't really know all consumer requirements, but AFAIK, usually
> when you want to program duty_cycle to 0 you also want to disable the PWM.

Note that hardware designers are "creative" and "disable the PWM" has
different semantics for different PWMs. Some PWMs just stop the output
at the level that it happens to be in, some stop in the inactive level,
some stop at 0, some stop driving the pin. Currently the intended
semantic of a disabled PWM is that it drives the inactive level (but it
might be smart and stop driving if there is a pull in the right
direction). I see no benefit of this semantic as it can also be
accomplished by setting .duty_cycle = 0, .period = $something_small.
Thierry doesn't agree and I fail to understand his reasoning.
> At least for the backlight case doesn't make sense program first the
> duty_cycle and then enable the PWM, is implicit, if duty_cycle is 0
> the PWM is disabled, if duty_cycle > 0 the PWM is enabled.

Yeah, that's my conclusion of above, too. After all the pwm_apply_state
function is there for being able to go from one state to each other
state with a single function call.

> > - A softer variant of the above: Should pwm_get_state() anticipate that
> > with .enabled = 0 the duty_cycle (and maybe also period) is
> > unreliable and cache that for callers?
>
> Sorry, when you say pwm_get_state(), you mean the core call or the lowlevel
> driver call?

The suggestion is to do what you do in the driver (i.e. remember
duty_cycle and in the general case also period) in the framework
instead and fix the problem for all lowlevel drivers that behave similar
to the implementation in question. i.e. don't rely on .duty_cycle and
.period having a sensible value after .get_state() if the PWM is off.
This is IMHO the second best option.

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
\
 
 \ /
  Last update: 2019-10-08 22:32    [W:0.600 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site