lkml.org 
[lkml]   [2019]   [Oct]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 5/7] dt-bindings: phy: tegra: Add Tegra194 support
Date
Extend the bindings to cover the set of features found in Tegra194.
Note that, technically, there are four more supplies connected to the
XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
, but the power sequencing requirements of Tegra194 require these to be
under the control of the PMIC.

Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it is
possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. To deal with
this, a new device node property "nvidia,disable-gen2" was added to
Tegra194 that be used to specifically disable Gen 2 speed for a
particular USB 3.0 port so that the port can be limited to Gen 1 speed
and avoid the instability.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
---
Changes in v3: none
Changes in v2:
- fix a typo

.../bindings/phy/nvidia,tegra124-xusb-padctl.txt | 16 ++++++++++++++++
1 file changed, 16 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
index 9fb682e47c29..59d870fa42e9 100644
--- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
+++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
@@ -37,6 +37,7 @@ Required properties:
- Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
- Tegra210: "nvidia,tegra210-xusb-padctl"
- Tegra186: "nvidia,tegra186-xusb-padctl"
+ - Tegra194: "nvidia,tegra194-xusb-padctl"
- reg: Physical base address and length of the controller's registers.
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must include the following entries:
@@ -62,6 +63,10 @@ For Tegra186:
- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.

+For Tegra194:
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+ 3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.

Pad nodes:
==========
@@ -154,6 +159,11 @@ For Tegra210, the list of valid PHY nodes is given below:
- sata: sata-0
- functions: "usb3-ss", "sata"

+For Tegra194, the list of valid PHY nodes is given below:
+- usb2: usb2-0, usb2-1, usb2-2, usb2-3
+ - functions: "xusb"
+- usb3: usb3-0, usb3-1, usb3-2, usb3-3
+ - functions: "xusb"

Port nodes:
===========
@@ -221,6 +231,9 @@ Optional properties:
is internal. In the absence of this property the port is considered to be
external.

+- nvidia,disable-gen2: A boolean property whose presence determines that a port
+ should be limited to USB 3.1 Gen 1. This property is only for Tegra194.
+
For Tegra124 and Tegra132, the XUSB pad controller exposes the following
ports:
- 3x USB2: usb2-0, usb2-1, usb2-2
@@ -233,6 +246,9 @@ For Tegra210, the XUSB pad controller exposes the following ports:
- 2x HSIC: hsic-0, hsic-1
- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3

+For Tegra194, the XUSB pad controller exposes the following ports:
+- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
+- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3

Examples:
=========
--
2.17.1
\
 
 \ /
  Last update: 2019-10-04 18:30    [W:0.076 / U:0.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site