lkml.org 
[lkml]   [2019]   [Oct]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
Date
Hello Bartosz,

Just a short note at this point.

On Mon, 2019-10-21 at 16:36 +0200, Bartosz Golaszewski wrote:
> pon., 21 paź 2019 o 09:00 Vaittinen, Matti
> <Matti.Vaittinen@fi.rohmeurope.com> napisał(a):
> > On Thu, 2019-10-17 at 14:45 +0200, Bartosz Golaszewski wrote:
> > > czw., 17 paź 2019 o 11:53 Matti Vaittinen
> > >
> > > > +static struct platform_driver bd71828_gpio = {
> > > > + .driver = {
> > > > + .name = "bd71828-gpio"
> > > > + },
> > > > + .probe = bd71828_probe,
> > > > +};
> > > > +
> > > > +module_platform_driver(bd71828_gpio);
> > > > +
> > > > +MODULE_AUTHOR("Matti Vaittinen <
> > > > matti.vaittinen@fi.rohmeurope.com>
> > > > ");
> > > > +MODULE_DESCRIPTION("BD71828 voltage regulator driver");
> > > > +MODULE_LICENSE("GPL");
> > >
> > > Don't you need a MODULE_ALIAS() here since this is an MFD sub-
> > > module?
> >
> > I must admit I don't know the details of how module loading is
> > done. I
> > used system where modules are load by scripts. (I guess the module
> > alias could be used to allow automatic module loading [by udev?])
> >
> > Can you please educate me - If I add module aliases matching the
> > sub-
> > device name given in in MFD cell - should the sub module loading be
> > automatic when MFD driver gets probed? For some reason I didn't get
> > that working on my test bed. Or maybe I misunderstood something.
> >
>
> If the gpio module is a sub-node on the device tree than you may need
> to use a sub-compatible to get the module loaded by udev.
>
> Bart
>
> > Eg, this should be enough for GPIO sub-module to be also load:
> >
> > MFD:
> > static struct mfd_cell bd71828_mfd_cells[] = {
> > { .name = "bd71828-pmic", },
> > { .name = "bd71828-gpio", },
> > ...
> > ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
> > bd71828_mfd_cells,
> > ARRAY_SIZE(bd71828_mfd_cells), NULL, 0,
> > regmap_irq_get_domain(irq_data));
> >
> > GPIO driver:
> > MODULE_ALIAS("platform:bd71828-gpio");
> >
> > I had the sub-devices probed even without the MODULE_ALIAS - but
> > manual
> > loading is required. I will gladly add the alias if it should
> > enable
> > the automatic module loading.

I had some problems with my test setup. After I fixed those I was able
to test the automatic module loading. The sub-devices do not need own
compatible to be load - they only need the correct module_alias:
"platform:sub-device-name-used-in-mfd-cell". If this is added, the
module for sub-device is load when MFD cell with name matching the
alias is instantiated.

So to your original question - yes, MODULE_ALIAS() is needed for
automated loading. No compatible is required then :)

Thanks for pointing me to correct direction here! It's always nice to
learn something new!

Br,
Matti Vaittinen
\
 
 \ /
  Last update: 2019-10-22 15:19    [W:0.133 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site