lkml.org 
[lkml]   [2019]   [Oct]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [v1,1/1] hwmon: (nct7904) Add array fan_alarm and vsen_alarm to store the alarms in nct7904_data struct.
On Thu, Sep 19, 2019 at 11:02:05AM +0800, Amy.Shih@advantech.com.tw wrote:
> From: "amy.shih" <amy.shih@advantech.com.tw>
>
> SMI# interrupt for fan and voltage is Two-Times Interrupt Mode.
> Fan or voltage exceeds high limit or going below low limit,
> it will causes an interrupt if the previous interrupt has been
> reset by reading all the interrupt Status Register. Thus, add the
> array fan_alarm and vsen_alarm to store the alarms for all of the
> fan and voltage sensors.
>
> Signed-off-by: amy.shih <amy.shih@advantech.com.tw>

Applied.

Thanks,
Guenter

> ---
> drivers/hwmon/nct7904.c | 22 ++++++++++++++++++++--
> 1 file changed, 20 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/hwmon/nct7904.c b/drivers/hwmon/nct7904.c
> index f62dd1882451..b26419dbe840 100644
> --- a/drivers/hwmon/nct7904.c
> +++ b/drivers/hwmon/nct7904.c
> @@ -99,6 +99,8 @@ struct nct7904_data {
> u8 enable_dts;
> u8 has_dts;
> u8 temp_mode; /* 0: TR mode, 1: TD mode */
> + u8 fan_alarm[2];
> + u8 vsen_alarm[3];
> };
>
> /* Access functions */
> @@ -214,7 +216,15 @@ static int nct7904_read_fan(struct device *dev, u32 attr, int channel,
> SMI_STS5_REG + (channel >> 3));
> if (ret < 0)
> return ret;
> - *val = (ret >> (channel & 0x07)) & 1;
> + if (!data->fan_alarm[channel >> 3])
> + data->fan_alarm[channel >> 3] = ret & 0xff;
> + else
> + /* If there is new alarm showing up */
> + data->fan_alarm[channel >> 3] |= (ret & 0xff);
> + *val = (data->fan_alarm[channel >> 3] >> (channel & 0x07)) & 1;
> + /* Needs to clean the alarm if alarm existing */
> + if (*val)
> + data->fan_alarm[channel >> 3] ^= 1 << (channel & 0x07);
> return 0;
> default:
> return -EOPNOTSUPP;
> @@ -298,7 +308,15 @@ static int nct7904_read_in(struct device *dev, u32 attr, int channel,
> SMI_STS1_REG + (index >> 3));
> if (ret < 0)
> return ret;
> - *val = (ret >> (index & 0x07)) & 1;
> + if (!data->vsen_alarm[index >> 3])
> + data->vsen_alarm[index >> 3] = ret & 0xff;
> + else
> + /* If there is new alarm showing up */
> + data->vsen_alarm[index >> 3] |= (ret & 0xff);
> + *val = (data->vsen_alarm[index >> 3] >> (index & 0x07)) & 1;
> + /* Needs to clean the alarm if alarm existing */
> + if (*val)
> + data->vsen_alarm[index >> 3] ^= 1 << (index & 0x07);
> return 0;
> default:
> return -EOPNOTSUPP;

\
 
 \ /
  Last update: 2019-10-02 15:44    [W:0.039 / U:9.924 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site