lkml.org 
[lkml]   [2019]   [Oct]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 1/3] dt-bindings: watchdog: sam9x60_wdt: add bindings
On 02/10/2019 07:35:23+0000, Eugen.Hristev@microchip.com wrote:
> From: Eugen Hristev <eugen.hristev@microchip.com>
>
> Add bindings for Microchip SAM9X60 Watchdog Timer
>
> It has the same bindings as
> Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
> except the compatible.
>

Maybe it can then use the same documentation file. However, I think you
should already use the yaml dt bindings schema instead of a simple text
file.

> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
> ---
> .../devicetree/bindings/watchdog/sam9x60-wdt.txt | 34 ++++++++++++++++++++++
> 1 file changed, 34 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/watchdog/sam9x60-wdt.txt
>
> diff --git a/Documentation/devicetree/bindings/watchdog/sam9x60-wdt.txt b/Documentation/devicetree/bindings/watchdog/sam9x60-wdt.txt
> new file mode 100644
> index 00000000..74b4e2d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/watchdog/sam9x60-wdt.txt
> @@ -0,0 +1,34 @@
> +* Microchip SAM9X60 Watchdog Timer (WDT) Controller
> +
> +Required properties:
> +- compatible: "microchip,sam9x60-wdt"
> +- reg: base physical address and length of memory mapped region.
> +
> +Optional properties:
> +- timeout-sec: watchdog timeout value (in seconds).
> +- interrupts: interrupt number to the CPU.
> +- atmel,watchdog-type: should be "hardware" or "software".
> + "hardware": enable watchdog fault reset. A watchdog fault triggers
> + watchdog reset.
> + "software": enable watchdog fault interrupt. A watchdog fault asserts
> + watchdog interrupt.
> +- atmel,idle-halt: present if you want to stop the watchdog when the CPU is
> + in idle state.
> + CAUTION: This property should be used with care, it actually makes the
> + watchdog not counting when the CPU is in idle state, therefore the
> + watchdog reset time depends on mean CPU usage and will not reset at all
> + if the CPU stop working while it is in idle state, which is probably
> + not what you want.
> +- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is
> + in debug state.
> +
> +Example:
> + watchdog@ffffff80 {
> + compatible = "microchip,sam9x60-wdt";
> + reg = <0xffffff80 0x24>;
> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 5>;
> + timeout-sec = <10>;
> + atmel,watchdog-type = "hardware";
> + atmel,dbg-halt;
> + atmel,idle-halt;
> + };
> --
> 2.7.4

--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

\
 
 \ /
  Last update: 2019-10-02 11:57    [W:0.100 / U:6.628 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site