lkml.org 
[lkml]   [2019]   [Oct]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 6/7] dt-bindings: soc: qcom: Extend RPMh power controller binding to describe thermal warming device
From
Date
On 10/17/2019 11:43 AM, Ulf Hansson wrote:
> On Thu, 17 Oct 2019 at 17:28, Thara Gopinath <thara.gopinath@linaro.org> wrote:
>>
>> Hello Ulf,
>> Thanks for the review!
>>
>> On 10/17/2019 05:04 AM, Ulf Hansson wrote:
>>> On Wed, 16 Oct 2019 at 21:37, Thara Gopinath <thara.gopinath@linaro.org> wrote:
>>>>
>>>> RPMh power controller hosts mx domain that can be used as thermal
>>>> warming device. Add a sub-node to specify this.
>>>>
>>>> Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
>>>> ---
>>>> Documentation/devicetree/bindings/power/qcom,rpmpd.txt | 10 ++++++++++
>>>> 1 file changed, 10 insertions(+)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
>>>> index eb35b22..fff695d 100644
>>>> --- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
>>>> +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
>>>> @@ -18,6 +18,16 @@ Required Properties:
>>>> Refer to <dt-bindings/power/qcom-rpmpd.h> for the level values for
>>>> various OPPs for different platforms as well as Power domain indexes
>>>>
>>>> += SUBNODES
>>>> +RPMh alsp hosts power domains that can behave as thermal warming device.
>>>> +These are expressed as subnodes of the RPMh. The name of the node is used
>>>> +to identify the power domain and must therefor be "mx".
>>>> +
>>>> +- #cooling-cells:
>>>> + Usage: optional
>>>> + Value type: <u32>
>>>> + Definition: must be 2
>>>> +
>>>
>>> Just wanted to express a minor thought about this. In general we use
>>> subnodes of PM domain providers to represent the topology of PM
>>> domains (subdomains), this is something different, which I guess is
>>> fine.
>>>
>>> I assume the #cooling-cells is here tells us this is not a PM domain
>>> provider, but a "cooling device provider"?
>> Yep.
>>>
>>> Also, I wonder if it would be fine to specify "power-domains" here,
>>> rather than using "name" as I think that is kind of awkward!?
>> Do you mean "power-domain-names" ? I am using this to match against the
>> genpd names defined in the provider driver.
>
> No. If you are using "power-domains" it means that you allow to
> describe the specifier for the provider.
Yep. But won't this look funny in DT ? The provider node will have a sub
node with a power domain referencing to itself Like below: Is this ok ?

rpmhpd: power-controller {
compatible = "qcom,sdm845-rpmhpd";
#power-domain-cells = <1>;

...
...
mx_cdev: mx {
#cooling-cells = <2>;
power-domains = <&rpmhpd SDM845_MX>;
};

>
> From Linux point of view, it means you can use dev_pm_domain_attach()
> to hook up the corresponding device with the PM domain.

Yes. Only the thermal framework does not populate cdev->dev->of_node.
But it should be a trivial thing to fix it. Also if I end up creating a
separate device, it should not matter.
>
> Using "power-domain-names" is just to allow to specify a name rather
> than an index, which makes sense if there is more than one index.
> Perhaps you can state that the "power-domain-names" should be there
> anyway, to be a little bit future proof if ever multiple index
> (multiple PM domains).
>
> Kind regards
> Uffe
>


--
Warm Regards
Thara

\
 
 \ /
  Last update: 2019-10-17 18:11    [W:0.060 / U:0.428 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site