lkml.org 
[lkml]   [2019]   [Jan]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 0/8] Add IPROC I2C slave mode and NIC I2C support
From
Date
Okay. Just noticed another thing. May I ask if you ran the
'get_maintaimner.pl' script to figure out the 'To:' and 'Cc:'?

I don't see Wolfram's name on on the To or Cc field of the emails you
send out:

Wolfram Sang <wsa@the-dreams.de>

6845 I2C SUBSYSTEM
6846 M: Wolfram Sang <wsa@the-dreams.de>
6847 L: linux-i2c@vger.kernel.org


Thanks,

Ray

On 1/8/2019 6:15 PM, Rayagonda Kokatanur wrote:
> Sorry for confusion. I made mistake in adding bcm-kernel-feedback-list
> while sending patch. Hence sent same patch set with updated email list. 
>
> Best regards,
> Rayagonda
>
>
>
> On Jan 8, 2019 10:55 PM, "Ray Jui" <ray.jui@broadcom.com
> <mailto:ray.jui@broadcom.com>> wrote:
>
> You sent out the same patch series 3 times without any explanation. Very
> confusing.
>
> Is this the latest one that should be reviewed?
>
> Thanks,
>
> Ray
>
>
> On 1/8/2019 1:16 AM, Rayagonda Kokatanur wrote:
> > Hi,
> > This patchset contains support for IPROC I2C slave and NIC I2C
> support.
> > Following are the brief changes done inorder to support both IPROC I2C
> > slave mode and NIC I2C,
> >
> > a. Add support to allow I2C rx transfer upto 255 bytes
> > b. Add polling mode support to the iProc I2C driver. Polling mode
> is used
> >    in certain SoCs where interrupt is not connected from the I2C
> block.
> > c. Add warpper read/write access for register to support indirect
> register
> >    access. This is required in certain SoCs with this iProc I2C
> >    block registered.
> >
> >
> > Ray Jui (1):
> >   dt-bindings: i2c: iproc: make 'interrupts' optional
> >
> > Rayagonda Kokatanur (5):
> >   i2c: iproc: add polling support
> >   i2c: iproc: use wrapper for read/write access
> >   dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
> >   i2c: iproc: add NIC I2C support
> >   arm64: dts: Stingray: Add NIC i2c device node
> >
> > Shreesha Rajashekar (2):
> >   i2c: iproc: I2C read up to 255 bytes support
> >   i2c: iproc: Add Slave mode support
> >
> >  .../devicetree/bindings/i2c/brcm,iproc-i2c.txt     |  14 +-
> >  .../arm64/boot/dts/broadcom/stingray/stingray.dtsi |  18 +
> >  drivers/i2c/busses/Kconfig                         |   1 +
> >  drivers/i2c/busses/i2c-bcm-iproc.c                 | 767
> +++++++++++++++++----
> >  4 files changed, 669 insertions(+), 131 deletions(-)
> >
>
>

\
 
 \ /
  Last update: 2019-01-09 19:29    [W:0.055 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site