lkml.org 
[lkml]   [2019]   [Jan]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 8/9] dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
On Wed, 30 Jan 2019 15:08:45 +0000
<Tudor.Ambarus@microchip.com> wrote:

> From: Tudor Ambarus <tudor.ambarus@microchip.com>
>
> The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
> access, the other for the qspi core and phy. Both are mandatory.
>
> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
> ---
> .../devicetree/bindings/spi/atmel-quadspi.txt | 28 ++++++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
> index e9dae6264d89..e7b7f297c5d7 100644
> --- a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
> +++ b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
> @@ -1,14 +1,22 @@
> * Atmel Quad Serial Peripheral Interface (QSPI)
>
> Required properties:
> -- compatible: Should be "atmel,sama5d2-qspi".
> +- compatible: Should be one of the following
> + - "atmel,sama5d2-qspi"
> + - "microchip,sam9x60-qspi"
> - reg: Should contain the locations and lengths of the base registers
> and the mapped memory.
> - reg-names: Should contain the resource reg names:
> - qspi_base: configuration register address space
> - qspi_mmap: memory mapped address space
> - interrupts: Should contain the interrupt for the device.
> -- clocks: The phandle of the clock needed by the QSPI controller.
> +- clocks: - "atmel,sama5d2-qspi": the phandle of the clock needed by the
> + QSPI controller.
> + - "microchip,sam9x60-qspi": should reference the peripheral
> + and system QSPI clocks.
> +- clock-names: Only for sam9x60 - should contain two strigs:

^strings

And I think naming clocks even for sama5d2 is a good practice, so I'd
suggest making "pclk" mandatory even if you support unnamed clk in the
driver to be backward compatible with old DTs.

> + - "pclk" for the peripheral clock
> + - "qspick" for the system clock
> - #address-cells: Should be <1>.
> - #size-cells: Should be <0>.
>
> @@ -29,3 +37,19 @@ spi@f0020000 {
> ...
> };
> };
> +
> +qspi@f0014000 {
> + compatible = "microchip,sam9x60-qspi";
> + reg = <0xf0014000 0x100>, <0x70000000 0x08000000>;
> + reg-names = "qspi_base", "qspi_mmap";
> + interrupts = <35 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_SYSTEM 19>;
> + clock-names = "pclk", "qspick";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> +
> + flash@0 {
> + ...
> + };
> +};

No need to add one example per compat, especially when all that
changes is the compat string and an extra clk.

\
 
 \ /
  Last update: 2019-01-30 18:32    [W:0.156 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site