lkml.org 
[lkml]   [2019]   [Jan]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/9] mfd: pm8xxx: convert to v2 irq interfaces to support hierarchical IRQ chips
On Fri, 25 Jan 2019, Brian Masney wrote:

> Convert the PM8XXX IRQ code to use the version 2 IRQ interface in order
> to support hierarchical IRQ chips. This is necessary so that ssbi-gpio
> can be setup as a hierarchical IRQ chip with PM8xxx as the parent. IRQ
> chips in device tree should be usable from the start without the
> having to make an additional call to gpio[d]_to_irq() to get the proper
> IRQ on the parent.
>
> The IRQ handler was hardcoded as handle_level_irq and this patch
> properly sets the handler to either handle_edge_irq or handle_level_irq
> depending on the IRQ type.
>
> pm8821_irq_domain_ops and pm8821_irq_domain_map are removed by this
> patch since the irq_chip is now contained in the pm_irq_data struct, and
> that allows us to use a common IRQ mapping function.
>
> This change was not tested on any actual hardware, however the same
> change was made to spmi-gpio and tested on a LG Nexus 5 (hammerhead)
> phone.
>
> Signed-off-by: Brian Masney <masneyb@onstation.org>
> ---
> drivers/mfd/qcom-pm8xxx.c | 86 +++++++++++++++++++++++----------------
> 1 file changed, 50 insertions(+), 36 deletions(-)
>
> diff --git a/drivers/mfd/qcom-pm8xxx.c b/drivers/mfd/qcom-pm8xxx.c
> index e6e8d81c15fd..a976890c4019 100644
> --- a/drivers/mfd/qcom-pm8xxx.c
> +++ b/drivers/mfd/qcom-pm8xxx.c
> @@ -70,20 +70,20 @@
> #define PM8XXX_NR_IRQS 256
> #define PM8821_NR_IRQS 112
>
> +struct pm_irq_data {
> + int num_irqs;
> + struct irq_chip *irq_chip;
> + void (*irq_handler)(struct irq_desc *desc);
> +};
> +
> struct pm_irq_chip {
> struct regmap *regmap;
> spinlock_t pm_irq_lock;
> struct irq_domain *irqdomain;
> - unsigned int num_irqs;
> unsigned int num_blocks;
> unsigned int num_masters;
> u8 config[0];
> -};
> -
> -struct pm_irq_data {
> - int num_irqs;
> - const struct irq_domain_ops *irq_domain_ops;
> - void (*irq_handler)(struct irq_desc *desc);
> + const struct pm_irq_data *pm_irq_data;
> };
>
> static int pm8xxx_read_block_irq(struct pm_irq_chip *chip, unsigned int bp,
> @@ -303,6 +303,7 @@ static int pm8xxx_irq_set_type(struct irq_data *d, unsigned int flow_type)
> {
> struct pm_irq_chip *chip = irq_data_get_irq_chip_data(d);
> unsigned int pmirq = irqd_to_hwirq(d);
> + irq_flow_handler_t flow_handler;
> int irq_bit;
> u8 block, config;
>
> @@ -316,6 +317,8 @@ static int pm8xxx_irq_set_type(struct irq_data *d, unsigned int flow_type)
> chip->config[pmirq] &= ~PM_IRQF_MASK_RE;
> if (flow_type & IRQF_TRIGGER_FALLING)
> chip->config[pmirq] &= ~PM_IRQF_MASK_FE;
> +
> + flow_handler = handle_edge_irq;
> } else {
> chip->config[pmirq] |= PM_IRQF_LVL_SEL;
>
> @@ -323,8 +326,12 @@ static int pm8xxx_irq_set_type(struct irq_data *d, unsigned int flow_type)
> chip->config[pmirq] &= ~PM_IRQF_MASK_RE;
> else
> chip->config[pmirq] &= ~PM_IRQF_MASK_FE;
> +
> + flow_handler = handle_level_irq;
> }
>
> + irq_set_handler_locked(d, flow_handler);
> +

Why don't you save yourself 3 lines of code and a variable and just
call irq_set_handler_locked() where you set flow_handler?

Apart from that nit, the code looks good to me.

--
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

\
 
 \ /
  Last update: 2019-01-30 14:28    [W:0.109 / U:7.288 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site