lkml.org 
[lkml]   [2019]   [Jan]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] phy: ti-pipe3: Add set_mode callback to configure usb3 phy as pcie phy
From
Date
Kishon,

On 30/01/19 12:59, Kishon Vijay Abraham I wrote:
> Hi Roger,
>
> On 30/01/19 4:18 PM, Roger Quadros wrote:
>> Hi Kishon,
>>
>> On 24/01/19 12:48, Kishon Vijay Abraham I wrote:
>>> DRA72 platform has the second instance of PHY shared between USB3
>>> controller and PCIe controller with default as USB3 controller.
>>> Since it is used with USB3 controller by default, it uses the
>>> compatible specific to USB (ti,omap-usb3).
>>>
>>> Populate set_mode callback so that the USB3 PHY can be configured
>>> to be used with PCIe controller.
>>
>> What is the use case of this? At what point and who decides the
>> phy_set_mode() to be called with USB vs PCIe?
>
> The PHY by default is configured to be used with USB controller (That's why it
> has a compatible of ti,omap-usb3). However there is a special case where this
> PHY has to be used PCIe controller. So the set_mode() will help the PHY driver
> to configure the USB PHY to be used with PCIe controller.
>
> This is not a shared PHY, so the PHY as such can be used only with USB or PCIe
> and is determined at designtime.

If type is defined at design time then the design using the PHY for PCIe shouldn't be
using "ti,omap-usb3" compatible. Right?

Maybe we should fix the DT? Which board/PHY is this about?

cheers,
-roger

>>
>>
>>>
>>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>>> ---
>>> drivers/phy/ti/phy-ti-pipe3.c | 66 ++++++++++++++++++++++++++++-------
>>> 1 file changed, 54 insertions(+), 12 deletions(-)
>>>
>>> diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c
>>> index 68ce4a082b9b..8c98f366416d 100644
>>> --- a/drivers/phy/ti/phy-ti-pipe3.c
>>> +++ b/drivers/phy/ti/phy-ti-pipe3.c
>>> @@ -56,6 +56,12 @@
>>>
>>> #define SATA_PLL_SOFT_RESET BIT(18)
>>>
>>> +#define PHY_RX_ANA_PRGRAMMABILITY_REG 0xC
>>> +#define MEM_EN_PLLBYP BIT(7)
>>> +
>>> +#define PHY_TX_TEST_CONFIG 0x2C
>>> +#define MEM_ENTESTCLK BIT(31)
>>> +
>>> #define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
>>> #define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14
>>>
>>> @@ -110,6 +116,8 @@
>>> #define PLL_IDLE_TIME 100 /* in milliseconds */
>>> #define PLL_LOCK_TIME 100 /* in milliseconds */
>>>
>>> +#define PIPE3_PHY_DISABLE_SYNC_POWER BIT(4)
>>> +
>>> struct pipe3_dpll_params {
>>> u16 m;
>>> u8 n;
>>> @@ -141,6 +149,7 @@ struct ti_pipe3 {
>>> unsigned int power_reg; /* power reg. index within syscon */
>>> unsigned int pcie_pcs_reg; /* pcs reg. index in syscon */
>>> bool sata_refclk_enabled;
>>> + u32 mode;
>>> };
>>>
>>> static struct pipe3_dpll_map dpll_map_usb[] = {
>>> @@ -233,7 +242,10 @@ static int ti_pipe3_power_on(struct phy *x)
>>> rate = rate / 1000000;
>>> mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
>>> OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK;
>>> - val = PIPE3_PHY_TX_RX_POWERON << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
>>> + val = PIPE3_PHY_TX_RX_POWERON;
>>> + if (phy->mode == PHY_MODE_PCIE)
>>> + val |= PIPE3_PHY_DISABLE_SYNC_POWER;
>>> + val <<= PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
>>> val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
>>>
>>> ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
>>> @@ -328,13 +340,11 @@ static void ti_pipe3_calibrate(struct ti_pipe3 *phy)
>>> ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_EQUALIZER, val);
>>> }
>>>
>>> -static int ti_pipe3_init(struct phy *x)
>>> +static int ti_pipe3_pcie_init(struct ti_pipe3 *phy)
>>> {
>>> - struct ti_pipe3 *phy = phy_get_drvdata(x);
>>> - u32 val;
>>> int ret = 0;
>>> + u32 val;
>>>
>>> - ti_pipe3_enable_clocks(phy);
>>> /*
>>> * Set pcie_pcs register to 0x96 for proper functioning of phy
>>> * as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
>>> @@ -353,10 +363,31 @@ static int ti_pipe3_init(struct phy *x)
>>> return ret;
>>>
>>> ti_pipe3_calibrate(phy);
>>> -
>>> - return 0;
>>> + } else {
>>> + val = ti_pipe3_readl(phy->phy_rx,
>>> + PHY_RX_ANA_PRGRAMMABILITY_REG);
>>> + val |= MEM_EN_PLLBYP;
>>> + ti_pipe3_writel(phy->phy_rx, PHY_RX_ANA_PRGRAMMABILITY_REG,
>>> + val);
>>> + val = ti_pipe3_readl(phy->phy_tx, PHY_TX_TEST_CONFIG);
>>> + val |= MEM_ENTESTCLK;
>>> + ti_pipe3_writel(phy->phy_tx, PHY_TX_TEST_CONFIG, val);
>>> }
>>>
>>> + return 0;
>>> +}
>>> +
>>> +static int ti_pipe3_init(struct phy *x)
>>> +{
>>> + struct ti_pipe3 *phy = phy_get_drvdata(x);
>>> + u32 val;
>>> + int ret = 0;
>>> +
>>> + ti_pipe3_enable_clocks(phy);
>>> +
>>> + if (phy->mode == PHY_MODE_PCIE)
>>> + return ti_pipe3_pcie_init(phy);
>>> +
>>> /* Bring it out of IDLE if it is IDLE */
>>> val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
>>> if (val & PLL_IDLE) {
>>> @@ -395,7 +426,7 @@ static int ti_pipe3_exit(struct phy *x)
>>> return 0;
>>>
>>> /* PCIe doesn't have internal DPLL */
>>> - if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
>>> + if (!(phy->mode == PHY_MODE_PCIE)) {
>>> /* Put DPLL in IDLE mode */
>>> val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
>>> val |= PLL_IDLE;
>>> @@ -429,11 +460,25 @@ static int ti_pipe3_exit(struct phy *x)
>>>
>>> return 0;
>>> }
>>> +
>>> +static int ti_pipe3_set_mode(struct phy *x, enum phy_mode mode, int submode)
>>> +{
>>> + struct ti_pipe3 *phy = phy_get_drvdata(x);
>>> +
>>> + if (phy->mode != PHY_MODE_INVALID)
>>> + return -EBUSY;
>>> +
>>> + phy->mode = mode;
>>
>> You are only saving the mode. But not really switching modes here.
>> How is this intended to work?
>
> The PHY doesn't have a specific mode. Rather it is a set of configurations
> required to operate in a particular mode.
>
> This mode value will be used in other init, power_on callback functions.
>
> Thanks
> Kishon
>

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

\
 
 \ /
  Last update: 2019-01-30 13:42    [W:0.063 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site