lkml.org 
[lkml]   [2019]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/2] ARM: dts: meson8b: odroidc1: Enable usb phy node
Hi Anand,

thank you for this patch!

On Sun, Jan 13, 2019 at 7:18 PM Anand Moon <linux.amoon@gmail.com> wrote:
>
> Add missing vbus-supply link to phy controller for usb_phy0
> and usb_phy1 nodes, this changes fixed the power issue
> on usb ports usb, changes help fix usb reset warning.
I trust you on the fact that GPIOAO_5 controls VBUS of USB0 and USB1

to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of the
USB_OTG controller (usb0)
- page 1 also shows a PWREN signal in the USB_HOST controller (usb1)
but not it's input
- based on your patch I assume that PWREN is the same signal for both
USB controllers

> [ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2
>
> Fixes: 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)
you already split your original patch into two, however I suggest
splitting these patches differently:
- this one (personally I would choose "ARM: dts: meson8b: odroidc1:
fix USB VBUS supplies" as title), which contains the Fixes tag, adds
the "usb_vbus" and references it in the "usb0" and "usb1" nodes
- enables usb0_phy and usb0 as part of your second patch (I would call
that "ARM: dts: meson8b: odroidc1: enable the OTG capable USB
controller")

> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> Cc: Jerome Brunet <jbrunet@baylibre.com>
> Cc: Neil Armstrong <narmstrong@baylibre.com>
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> Rebased on Kevin's amlogic/v5.0/fixes branch
>
> [alarm@archl-c1t ~]$ lsusb -t
> /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
> |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
> |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
> |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
> |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
> |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M
> |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M
> [alarm@archl-c1t ~]$
> [alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
> Couldn't open device, some information will be missing
> Bus 001 Device 003: ID 1b71:0056 Fushicai
> MaxPower 500mA
> Couldn't open device, some information will be missing
> Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
> MaxPower 30mA
> Couldn't open device, some information will be missing
> Couldn't open device, some information will be missing
> Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
> MaxPower 100mA
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> MaxPower 0mA
> ---
> arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++
> 1 file changed, 23 insertions(+)
>
> diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
> index 0f0a46ddf3ff..a49a8509b288 100644
> --- a/arch/arm/boot/dts/meson8b-odroidc1.dts
> +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
> @@ -83,6 +83,19 @@
> regulator-max-microvolt = <5000000>;
> };
>
> + usb_vbus: regulator-usb-vbus {
please add a comment here with some details about the regulator and
add a hint that the signal in the schematics is called "PWREN"

> + compatible = "regulator-fixed";
> +
> + regulator-name = "USB_VBUS";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + vin-supply = <&p5v0>;
> +
> + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> tflash_vdd: regulator-tflash_vdd {
> /*
> * signal name from schematics: TFLASH_VDD_EN
> @@ -293,8 +306,18 @@
> pinctrl-names = "default";
> };
>
> +&usb0_phy {
> + status = "okay";
> + vbus-supply = <&usb_vbus>;
> +};
> +
> &usb1_phy {
> status = "okay";
> + vbus-supply = <&usb_vbus>;
> +};
> +
> +&usb0 {
> + status = "okay";
> };
I believe there's a problem with the usb/usb_phy nodes here. on my
Odroid-C1 this results in:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS
USB_VBUS 0 0 0 unknown 5000mV 0mA
5000mV 5000mV
(open count is 0)

if I move "vbus-supply" to the "usb1" node (just as an example) then I get:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS
USB_VBUS 1 1 0 unknown 5000mV 0mA
5000mV 5000mV

unfortunately neither your original patch nor the modified version
seem to enable USB VBUS on my Odroid-C1.
I have documented my findings already back in December, see "USB
issues on Odroid-C1" [0]
help on that would be highly appreciated :)

on which board revision have you tested this patch?


Regards
Martin


[0] http://lists.infradead.org/pipermail/linux-amlogic/2018-December/009451.html

\
 
 \ /
  Last update: 2019-01-18 23:30    [W:0.123 / U:12.784 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site