lkml.org 
[lkml]   [2019]   [Jan]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v8 1/3] Bluetooth: hci_qca: use wait_until_sent() for power pulses
Date
wcn3990 requires a power pulse to turn ON/OFF along with
regulators. Sometimes we are observing the power pulses are sent
out with some time delay, due to queuing these commands. This is
causing synchronization issues with chip, which intern delay the
chip setup or may end up with communication issues.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
---
Changes in v8:
* Updated 1 second timeout instead of indefinite wait.

Changes in v7:
* updated the wait time to 5 ms after sending power pulses.

Changes in v6:
* added serdev_device_write_flush() in qca_send_power_pulse
instead during the power off pulse.

Changes in v5:
* added serdev_device_write_flush() in qca_power_off().
---
drivers/bluetooth/hci_qca.c | 46 ++++++++++++++++---------------------
1 file changed, 20 insertions(+), 26 deletions(-)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index f036c8f98ea3..681bfa30467e 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -60,6 +60,7 @@
#define IBS_WAKE_RETRANS_TIMEOUT_MS 100
#define IBS_TX_IDLE_TIMEOUT_MS 2000
#define BAUDRATE_SETTLE_TIMEOUT_MS 300
+#define POWER_PULSE_TRANS_TIMEOUT_MS 1000

/* susclk rate */
#define SUSCLK_RATE_32KHZ 32768
@@ -1013,11 +1014,10 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
hci_uart_set_baudrate(hu, speed);
}

-static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
+static int qca_send_power_pulse(struct hci_uart *hu, u8 cmd)
{
- struct hci_uart *hu = hci_get_drvdata(hdev);
- struct qca_data *qca = hu->priv;
- struct sk_buff *skb;
+ int ret;
+ int timeout = __msecs_to_jiffies(POWER_PULSE_TRANS_TIMEOUT_MS);

/* These power pulses are single byte command which are sent
* at required baudrate to wcn3990. On wcn3990, we have an external
@@ -1029,22 +1029,22 @@ static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
* save power. Disabling hardware flow control is mandatory while
* sending power pulses to SoC.
*/
- bt_dev_dbg(hdev, "sending power pulse %02x to SoC", cmd);
-
- skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
- if (!skb)
- return -ENOMEM;
+ bt_dev_dbg(hu->hdev, "sending power pulse %02x to controller", cmd);

+ serdev_device_write_flush(hu->serdev);
hci_uart_set_flow_control(hu, true);
+ ret = serdev_device_write_buf(hu->serdev, &cmd, sizeof(cmd));
+ if (ret < 0) {
+ bt_dev_err(hu->hdev, "failed to send power pulse %02x", cmd);
+ return ret;
+ }

- skb_put_u8(skb, cmd);
- hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
-
- skb_queue_tail(&qca->txq, skb);
- hci_uart_tx_wakeup(hu);
-
- /* Wait for 100 uS for SoC to settle down */
- usleep_range(100, 200);
+ serdev_device_wait_until_sent(hu->serdev, timeout);
+ /* Wait of 5ms is required for assuring to send the byte on the Tx
+ * line and also for the controller to settle down for the received
+ * byte.
+ */
+ usleep_range(5000, 6000);
hci_uart_set_flow_control(hu, false);

return 0;
@@ -1116,7 +1116,6 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)

static int qca_wcn3990_init(struct hci_uart *hu)
{
- struct hci_dev *hdev = hu->hdev;
struct qca_serdev *qcadev;
int ret;

@@ -1139,12 +1138,12 @@ static int qca_wcn3990_init(struct hci_uart *hu)

/* Forcefully enable wcn3990 to enter in to boot mode. */
host_set_baudrate(hu, 2400);
- ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE);
+ ret = qca_send_power_pulse(hu, QCA_WCN3990_POWEROFF_PULSE);
if (ret)
return ret;

qca_set_speed(hu, QCA_INIT_SPEED);
- ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWERON_PULSE);
+ ret = qca_send_power_pulse(hu, QCA_WCN3990_POWERON_PULSE);
if (ret)
return ret;

@@ -1274,13 +1273,8 @@ static const struct qca_vreg_data qca_soc_data = {

static void qca_power_shutdown(struct hci_uart *hu)
{
- struct serdev_device *serdev = hu->serdev;
- unsigned char cmd = QCA_WCN3990_POWEROFF_PULSE;
-
host_set_baudrate(hu, 2400);
- hci_uart_set_flow_control(hu, true);
- serdev_device_write_buf(serdev, &cmd, sizeof(cmd));
- hci_uart_set_flow_control(hu, false);
+ qca_send_power_pulse(hu, QCA_WCN3990_POWEROFF_PULSE);
qca_power_setup(hu, false);
}

--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
\
 
 \ /
  Last update: 2019-01-16 12:47    [W:0.074 / U:0.492 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site