lkml.org 
[lkml]   [2019]   [Jan]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH V7 2/2] drm/panel: Add Sitronix ST7701 panel driver
On Sat, Jan 12, 2019 at 2:49 AM Sam Ravnborg <sam@ravnborg.org> wrote:
>
> Hi Jagan.
>
> Gave this another more detailed read - triggered some additional comments.
> Depite the comments it looks good, and this is all more or
> less cosmetic improvements.

Thanks for the review.

>
> Sam
>
> > +struct st7701_panel_desc {
> > + const struct drm_display_mode *mode;
> > + unsigned int lanes;
> > + unsigned long flags;
> > + enum mipi_dsi_pixel_format format;
> > + const char *const *supply_names;
> > + unsigned int num_supplies;
> > + unsigned int panel_sleep_delay;
> > +};
> > +
> > +struct st7701 {
> > + struct drm_panel panel;
> > + struct mipi_dsi_device *dsi;
> > + const struct st7701_panel_desc *desc;
> > +
> > + struct backlight_device *backlight;
> > + struct regulator_bulk_data *supplies;
> > + unsigned int num_supplies;
> I cannot see that num_supplies in this struct are used?

Yes it is used in the code, please check in struct st7701_panel_desc.

>
>
> > + struct gpio_desc *reset;
> > + unsigned int sleep_delay;
> > +};
> > +
> > +static inline struct st7701 *panel_to_st7701(struct drm_panel *panel)
> > +{
> > + return container_of(panel, struct st7701, panel);
> > +}
> > +
> > +static inline int st7701_dsi_write(struct st7701 *st7701, const void *seq,
> > + size_t len)
> > +{
> > + return mipi_dsi_dcs_write_buffer(st7701->dsi, seq, len);
> > +}
> > +
>
>
> > +static int st7701_prepare(struct drm_panel *panel)
> > +{
> > + struct st7701 *st7701 = panel_to_st7701(panel);
> > + int ret;
> > +
> > + gpiod_set_value(st7701->reset, 0);
> > + msleep(20);
> > +
> > + ret = regulator_bulk_enable(st7701->desc->num_supplies,
> > + st7701->supplies);
> > + if (ret < 0)
> > + return ret;
> > + msleep(20);
> > +
> > + gpiod_set_value(st7701->reset, 1);
> > + msleep(20);
> > +
> > + gpiod_set_value(st7701->reset, 0);
> > + msleep(30);
> > +
> > + gpiod_set_value(st7701->reset, 1);
> > + msleep(150);
> > +
> > + st7701_init_sequence(st7701);
> > +
> > + return 0;
> > +}
> > +
>
> > +static int st7701_unprepare(struct drm_panel *panel)
> > +{
> > + struct st7701 *st7701 = panel_to_st7701(panel);
> > +
> > + ST7701_DSI(st7701, MIPI_DCS_EXIT_SLEEP_MODE, 0x00);
> > +
> > + msleep(st7701->sleep_delay);
> > +
> > + gpiod_set_value(st7701->reset, 0);
> > +
> > + gpiod_set_value(st7701->reset, 1);
> > +
> > + gpiod_set_value(st7701->reset, 0);
> No timing constrains here? In prepare there are sleeps intermixed.

Delay while doing unprare is not needed I suppose.

>
> > +
> > + regulator_bulk_disable(st7701->desc->num_supplies, st7701->supplies);
> > +
> > + return 0;
> > +}
> > +
> > +static int st7701_get_modes(struct drm_panel *panel)
> > +{
> > + struct st7701 *st7701 = panel_to_st7701(panel);
> > + const struct drm_display_mode *desc_mode = st7701->desc->mode;
> > + struct drm_display_mode *mode;
> > +
> > + mode = drm_mode_duplicate(panel->drm, desc_mode);
> > + if (!mode) {
> > + dev_err(&st7701->dsi->dev, "failed to add mode %ux%ux@%u\n",
> > + desc_mode->hdisplay, desc_mode->vdisplay,
> > + desc_mode->vrefresh);
> Use something like:
> DRM_DEV_ERROR(st7701->dev, "failed to add mode" DRM_MODE_FMT ",
> DRM_MODE_ARG(desc_mode));
>
> > + return -ENOMEM;
> > + }
> > +
> > + drm_mode_set_name(mode);
> > + drm_mode_probed_add(panel->connector, mode);
> > +
> > + panel->connector->display_info.width_mm = desc_mode->width_mm;
> > + panel->connector->display_info.height_mm = desc_mode->height_mm;
> > +
> > + return 1;
> > +}
> > +
>
> > +static const struct st7701_panel_desc ts8550b_desc = {
> > + .mode = &ts8550b_mode,
> > + .lanes = 2,
> > + .flags = MIPI_DSI_MODE_VIDEO,
> > + .format = MIPI_DSI_FMT_RGB888,
> > + .supply_names = ts8550b_supply_names,
> > + .num_supplies = ARRAY_SIZE(ts8550b_supply_names),
> > + .panel_sleep_delay = 80, /* panel need extra 80ms for sleep out cmd */
> In the only place this is used there is added 120 ms too.
> Looks inconsistent - do we have the same delay twice?

120ms is the one recommended by st7701 controller delay after a sleep
out command, please check it in datasheet [1], page 188. And this 80ms
is specific to TS8550B panel as per BSP code this doesn't have proper
documentation but the BSP code doing this extra 80ms.

>
>
> > +
> > +static int st7701_dsi_probe(struct mipi_dsi_device *dsi)
> > +{
> > + const struct st7701_panel_desc *desc;
> > + struct device_node *np;
> > + struct st7701 *st7701;
> > + int ret, i;
> > +
> > + st7701 = devm_kzalloc(&dsi->dev, sizeof(*st7701), GFP_KERNEL);
> > + if (!st7701)
> > + return -ENOMEM;
> > +
> > + desc = of_device_get_match_data(&dsi->dev);
> > + dsi->mode_flags = desc->flags;
> > + dsi->format = desc->format;
> > + dsi->lanes = desc->lanes;
> > +
> > + st7701->supplies = devm_kcalloc(&dsi->dev, desc->num_supplies,
> > + sizeof(*st7701->supplies),
> > + GFP_KERNEL);
> > + if (!st7701->supplies)
> > + return -ENOMEM;
> > +
> > + for (i = 0; i < desc->num_supplies; i++)
> > + st7701->supplies[i].supply = desc->supply_names[i];
> > +
> > + ret = devm_regulator_bulk_get(&dsi->dev, desc->num_supplies,
> > + st7701->supplies);
> > + if (ret < 0)
> > + return ret;
> > +
> > + st7701->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW);
> > + if (IS_ERR(st7701->reset)) {
> > + dev_err(&dsi->dev, "Couldn't get our reset GPIO\n");
> > + return PTR_ERR(st7701->reset);
> > + }
> > +
> > + np = of_parse_phandle(dsi->dev.of_node, "backlight", 0);
> > + if (np) {
> > + st7701->backlight = of_find_backlight_by_node(np);
> > + of_node_put(np);
> > +
> > + if (!st7701->backlight)
> > + return -EPROBE_DEFER;
> > + }
> This is a simpler variant of the above:
> st7701->backlight = devm_of_find_backlight(dsi->dev);
> if (IS_ERR(st7701->backlight))
> return PTR_ERR(st7701->backlight);
>
> Suggested by Noralf in another thread for a similar driver.
>
>
> > +
> > + drm_panel_init(&st7701->panel);
> > +
> > + /* We need to wait 120ms after a sleep out command */
> > + st7701->sleep_delay = 120 + desc->panel_sleep_delay;
> This is the other place where we add 120 to the previous 80 - in total 200 ms.

Please see above comment.

[1] http://www.startek-lcd.com/res/starteklcd/pdres/201705/20170512144242904.pdf

\
 
 \ /
  Last update: 2019-01-12 04:47    [W:0.155 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site