lkml.org 
[lkml]   [2019]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 6/7] arm64: dts: sdm845: Increase alert trip point to 95 degrees
On Fri, Jan 11, 2019 at 01:15:09AM +0530, Amit Kucheria wrote:
> On Thu, Jan 10, 2019 at 7:45 AM Matthias Kaehlcke <mka@chromium.org> wrote:
> >
> > On Wed, Jan 09, 2019 at 05:15:33PM -0800, Matthias Kaehlcke wrote:
> > > Hi Amit,
> > >
> > > On Thu, Jan 10, 2019 at 05:30:55AM +0530, Amit Kucheria wrote:
> > > > 75 degrees is too aggressive for throttling the CPU. After speaking to
> > > > Qualcomm engineers, increase it to 95 degrees.
> > > >
> > > > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > > > ---
> > > > arch/arm64/boot/dts/qcom/sdm845.dtsi | 16 ++++++++--------
> > > > 1 file changed, 8 insertions(+), 8 deletions(-)
> > > >
> > > > diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > > > index c27cbd3bcb0a..29e823b0caf4 100644
> > > > --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > > > +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > > > @@ -1692,7 +1692,7 @@
> > > >
> > > > trips {
> > > > cpu_alert0: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1713,7 +1713,7 @@
> > > >
> > > > trips {
> > > > cpu_alert1: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1734,7 +1734,7 @@
> > > >
> > > > trips {
> > > > cpu_alert2: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1755,7 +1755,7 @@
> > > >
> > > > trips {
> > > > cpu_alert3: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1776,7 +1776,7 @@
> > > >
> > > > trips {
> > > > cpu_alert4: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1797,7 +1797,7 @@
> > > >
> > > > trips {
> > > > cpu_alert5: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1818,7 +1818,7 @@
> > > >
> > > > trips {
> > > > cpu_alert6: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > > > @@ -1839,7 +1839,7 @@
> > > >
> > > > trips {
> > > > cpu_alert7: trip0 {
> > > > - temperature = <75000>;
> > > > + temperature = <95000>;
> > > > hysteresis = <2000>;
> > > > type = "passive";
> > > > };
> > >
> > > The change itself looks good to me, however I wonder if it would be
> > > worth to eliminate redundancy and merge the current 8 thermal zones
> > > into 2, one for the Silver and one for the Gold cluster (as done by
> > > http://crrev.com/c/1381752). There is a single cooling device for
> > > each cluster, so it's not clear to me if there is any gain from having
> > > a separate thermal zone for each CPU. If it is important to monitor
> > > the temperatures of the individual cores this can still be done by
> > > configuring the thermal zone of the cluster with multiple thermal
> > > sensors.
> >
> > I see your idea is to have a cooling device per CPU ("arm64: dts:
> > sdm845: wireup the thermal trip points to cpufreq" /
> > https://lore.kernel.org/patchwork/patch/1030742/), however that
> > doesn't work as intended. Only two cpufreq 'devices' are created,
> > one for CPU0 and one for CPU4. In consequence cpufreq->ready() only
> > runs for these cores and only two cooling devices are
> > registered. Since the cores of a cluster all run at the same
> > frequency I also doubt if having multiple cooling devices would
> > bring any benefits.
>
> I actually only intended for two cooling devices - one for each
> frequency domain. I'll clarify it better in the patch description.

Viresh helped me understand that we currently need to add cooling
device entries for all CPUs to the DT, even though at most one will be
active per freq domain at any time (I wonder if this could be changed
though).

Independently of the cooling devices, is there any value in having a
thermal zone for each CPU instead of having only one per freq domain?

Thanks

Matthias

\
 
 \ /
  Last update: 2019-01-10 21:00    [W:0.112 / U:0.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site