lkml.org 
[lkml]   [2019]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC PATCH 1/3] can: m_can: Create m_can core to leverage common code
From
Date
Faiz

On 1/10/19 1:57 AM, Rizvi, Mohammad Faiz Abbas wrote:
> Hi Dan, Wolfgang,
>
> On 1/10/2019 1:14 PM, Wolfgang Grandegger wrote:
>> Hello Dan,
>>
>> sorry for my late response on that topic...
>>
>> Am 09.01.19 um 21:58 schrieb Dan Murphy:
>>> Wolfgang
>>>
>>> On 11/3/18 5:45 AM, Wolfgang Grandegger wrote:
>>>> Hello Dan,
>>>>
>>>> Am 31.10.2018 um 21:15 schrieb Dan Murphy:
>>>>> Wolfgang
>>>>>
>>>>> Thanks for the review
>>>>>
>>>>> On 10/27/2018 09:19 AM, Wolfgang Grandegger wrote:
>>>>>> Hello Dan,
>>>>>>
>>>>>> for the RFC, could you please just do the necessary changes to the
>>>>>> existing code. We can discuss about better names, etc. later. For
>>>>>> the review if the common code I quickly did:
>>>>>>
>>>>>>    mv m_can.c m_can_platform.c
>>>>>>    mv m_can_core.c m_can.c
>>>>>>
>>>>>> The file names are similar to what we have for the C_CAN driver.
>>>>>>
>>>>>>    s/classdev/priv/
>>>>>>    variable name s/m_can_dev/priv/
>>>>>>
>>>>>> Then your patch 1/3 looks as shown below. I'm going to comment on that
>>>>>> one. The comments start with "***"....
>>>>>>
>>>>>
>>>>> So you would like me to align the names with the c_can driver?
>>>>
>>>> That would be the obvious choice.
>>>>> <snip>
>>>>>>
>>>>>> *** I didn't review the rest of the patch for now.
>>>>>>
>>>>>
>>>>> snipped the code to reply to the comment.
>>>>>
>>>>>> Looking to the generic code, you didn't really change the way
>>>>>> the driver is accessing the registers. Also the interrupt handling
>>>>>> and rx polling is as it was before. Does that work properly using
>>>>>> the SPI interface of the TCAN4x5x?
>>>>>
>>>>> I don't want to change any of that yet.  Maybe my cover letter was not clear
>>>>> or did not go through.
>>>>>
>>>>> But the intention was just to break out the functionality to create a MCAN framework
>>>>> that can be used by devices that contain the Bosch MCAN core and provider their own protocal to access
>>>>> the registers in the device.
>>>>>
>>>>> I don't want to do any functional changes at this time on the IP code itself until we have a framework.
>>>>> There should be no regression in the io mapped code.
>>>>>
>>>>> I did comment on the interrupt handling and asked if a threaded work queue would affect CAN timing.
>>>>> For the original TCAN driver this was the way it was implemented.
>>>>
>>>> Do threaded interrupts with RX polling make sense? I think we need a
>>>> common interface allowing to select hard-irqs+napi or threaded-irqs.
>>>>
>>>
>>> I have been working on this code for about a month now and I am *not happy* with the amount of change that needs
>>> to be done to make the m_can a framework.
>>>
>>> I can tx/rx frames from another CAN device to the TCAN part but I have not even touched the iomapped code.
>>>
>>> The challenging part is that the m_can code that is currently available does not have to worry about atomic context because
>>> there is no peripheral waiting.  Since the TCAN is a peripheral device we need to take into about the hard waits in IRQ context
>>> as well as the atomic context.  Doing this creates many deltas in the base code that may break iomapped devices.  I have had to
>>> add the thread_irqs and now I am in the midst of the issue you brought up with napi.  I would have to schedule a queue for perp devices
>>> and leave the non-threaded iomapped irq.
>>>
>>> At this point I think it may be wise to leave the m_can code alone as it is working and stable and just work on the TCAN driver as
>>> a standalone driver.  A framework would be nice but I think it would destablize the m_can driver which is embedded in many SoC's and
>>> we cannot possibly test everyone of them.
>>
>> Unfortunately, I do not have m_can hardware at hand.
>
> There are exactly 3 platforms in mainline that use the m_can driver. I can help Dan test it on a dra76x. I haven't had a chance to look at the changes in depth, but just testing for regressions on existing platforms shouldn't be too hard once we have it working on one.
>

Thanks Faiz. Once I have the TCAN fully working I will post the branch to my repo.

Dan

> Thanks,
> Faiz
>
>>
>>> What are your thoughts?
>>
>> What we need is a common set of functions doing tx, rx, error and state
>> handling. This will requires substantial changes to the existing
>> io-mapped m_can driver, of course. I still believe it's worth the
>> effort, but I agree that it's difficult for you to re-write and test the
>> existing m_can driver.
>>
>> What about implementing such a set of common functions plus the SPI
>> specific part for your TCAN device. What do you/others think?
>>
>> Wolfgang.
>>


--
------------------
Dan Murphy

\
 
 \ /
  Last update: 2019-01-10 13:55    [W:0.063 / U:13.612 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site