lkml.org 
[lkml]   [2018]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] ARM: dts: exynos: Add CD and WP pins to Odroid XU SD card
On Mon, Sep 24, 2018 at 12:04:52PM +0200, Marek Szyprowski wrote:
> Hi Krzysztof,
>
> On 2018-09-21 23:03, Krzysztof Kozlowski wrote:
> > Defining card-detect and write-protect GPIO pins in Odroid XU SD Card
> > does not change anything from functional point of view - dw-mmc driver
> > was reading the state from registers. Adding cd-gpios and wp-gpios
> > properties changes only internal driver behavior to access the pins
> > directly.
> >
> > Add them to DTS only to comprehensively describe the hardware. Minor
> > benefit is that write-protect pin configuration makes sure that it will
> > be properly pulled up to indicate write access.
> >
> > This also removes debug messages:
> > dwmmc_exynos 12220000.mmc: No GPIO consumer cd found
> > dwmmc_exynos 12220000.mmc: No GPIO consumer wp found
> >
> > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> > ---
> > arch/arm/boot/dts/exynos5410-odroidxu.dts | 12 +++++++++++-
> > 1 file changed, 11 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
> > index a2046f5f998c..dae360f29a47 100644
> > --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
> > +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
> > @@ -525,12 +525,14 @@
> >
> > &mmc_2 {
> > status = "okay";
> > + wp-gpios = <&gpm5 0 GPIO_ACTIVE_LOW>;
> > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_LOW>;
> > card-detect-delay = <200>;
> > samsung,dw-mshc-ciu-div = <3>;
> > samsung,dw-mshc-sdr-timing = <0 4>;
> > samsung,dw-mshc-ddr-timing = <0 2>;
> > pinctrl-names = "default";
> > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
> > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4 &sd2_wp>;
>
> IMHO there is no point adding cd-gpios property if CD line is already
> assigned to this device via respective pin ctrl entry (as special function).
>
> Handling of WP line is even more controversial imho. Ideally the drivers
> or mmc core should check somehow if WP line is available or not and act
> respectively. WP line is not available on uSD card connector so there is
> no point describing it.

Thanks for comments. In that case I'll add only the pin configuration to
be sure that pin stays pulled up.

Best regards,
Krzysztof

>
> > bus-width = <4>;
> > cap-sd-highspeed;
> > vmmc-supply = <&ldo21_reg>;
> > @@ -573,6 +575,14 @@
> > samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
> > };
> > +
> > + sd2_wp: sd2-wp {
> > + samsung,pins = "gpm5-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + /* Pin is floating so pull it up to disable write-protect */
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
> > + };
> > };
> >
> > &pwm {
>
> Best regards
> --
> Marek Szyprowski, PhD
> Samsung R&D Institute Poland
>

\
 
 \ /
  Last update: 2018-09-26 18:13    [W:1.634 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site