lkml.org 
[lkml]   [2018]   [Sep]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 3/4] [media] ad5820: DT new optional field enable-gpios
Hi
On Thu, Sep 20, 2018 at 10:23 PM Laurent Pinchart
<laurent.pinchart@ideasonboard.com> wrote:
>
> On Thursday, 20 September 2018 23:21:28 EEST Laurent Pinchart wrote:
> > Hi Ricardo,
> >
> > Thank you for the patch.
> >
> > On Thursday, 20 September 2018 19:19:11 EEST Ricardo Ribalda Delgado wrote:
> > > Document new enable-gpio field. It can be used to disable the part
> > > without turning down its regulator.
> > >
> > > Cc: devicetree@vger.kernel.org
> > > Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
> > > ---
> > >
> > > Documentation/devicetree/bindings/media/i2c/ad5820.txt | 6 ++++++
> > > 1 file changed, 6 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt
> > > b/Documentation/devicetree/bindings/media/i2c/ad5820.txt index
> > > 5940ca11c021..07d577bb37f7 100644
> > > --- a/Documentation/devicetree/bindings/media/i2c/ad5820.txt
> > > +++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
> > >
> > > @@ -8,6 +8,11 @@ Required Properties:
> > > - VANA-supply: supply of voltage for VANA pin
> > >
> > > +Optional properties:
> > > +
> > > + - enable-gpios : GPIO spec for the XSHUTDOWN pin.
> >
> > xshutdown is active-low, so enable is active-high. Should this be documented
> > explicitly, to avoid polarity errors ? Maybe something along the lines of
> >
> > - enable-gpios: GPIO spec for the XSHUTDOWN pin. Note that the polarity of
> > the enable GPIO is the opposite of the XSHUTDOWN pin (asserting the enable
> > GPIO deasserts the XSHUTDOWN signal and vice versa).

Agreed

>
> Or alternatively you could name the property xshutdown-gpios, as explained in
> my (incorrect) review of 2/4.

I have double negatives :). If there is no other option I will rename
it xshutdown, but I want to give it a try to enable.

>
> > > If specified, it will be
> > > + asserted when VANA-supply is enabled.
> >
> > That documents a driver behaviour, is it needed in DT ?
> >
> > > Example:
> > > ad5820: coil@c {
> > >
> > > @@ -15,5 +20,6 @@ Example:
> > > reg = <0x0c>;
> > > VANA-supply = <&vaux4>;
> > >
> > > + enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
> > > };
>
>
> --
> Regards,
>
> Laurent Pinchart
>
>
>


--
Ricardo Ribalda

\
 
 \ /
  Last update: 2018-09-20 22:27    [W:0.935 / U:1.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site