lkml.org 
[lkml]   [2018]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/8] dt-bindings: mmc: Add DQS trim value to Tegra SDHCI
On Thu, Aug 09, 2018 at 02:45:15PM +0300, Aapo Vienamo wrote:
> On Thu, 9 Aug 2018 13:36:09 +0200
> Thierry Reding <thierry.reding@gmail.com> wrote:
>
> > On Tue, Aug 07, 2018 at 04:59:57PM +0300, Aapo Vienamo wrote:
> > > Document HS400 DQS trim value device tree property.
> > >
> > > Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
> > > ---
> > > Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt | 3 +++
> > > 1 file changed, 3 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
> > > index 3c7960a..7d294f3 100644
> > > --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
> > > +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
> > > @@ -72,6 +72,7 @@ Optional properties for Tegra210 and Tegra186:
> > > trimmer value for non-tunable modes.
> > > - nvidia,default-trim : Specify the default outbound clock trimmer
> > > value.
> > > +- nvidia,dqs-trim : Specify DQS trim value for HS400 timing
> > >
> > > Notes on the pad calibration pull up and pulldown offset values:
> > > - The property values are drive codes which are programmed into the
> > > @@ -88,6 +89,8 @@ Optional properties for Tegra210 and Tegra186:
> > > - The values are programmed to the Vendor Clock Control Register.
> > > Please refer to the reference manual of the SoC for correct
> > > values.
> > > + - The DQS trim values are only used on controllers which support
> > > + HS400 timing.
> >
> > One of these additions says "DQS trim values", the other says "DQS trim
> > value". It is unclear from the above how many values there are. I think
> > this should be more explicit. Also, I don't see why the note about which
> > controllers the DQS trim value(s) applies to is in a separate paragraph.
> > Couldn't it be moved to the property description?
>
> It's a single value. The plural form is a mistake.
>
> > Also, I think the bindings should specify which generations of Tegra do
> > support HS400. Where else are people supposed to find that information?
>
> This property is under the "Optional properties for Tegra210 and
> Tegra186" section and it only applies for the said generations.

What's the point of specifying that they are only used on controllers
which support HS400? Are you saying that only a subset of the SDHCI
controllers on Tegra210 and Tegra186 support HS400?

Thierry
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-08-09 15:47    [W:0.555 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site