lkml.org 
[lkml]   [2018]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 12/40] mmc: tegra: Reconfigure pad voltages during voltage switching
On Thu, Aug 09, 2018 at 03:52:39PM +0300, Aapo Vienamo wrote:
> On Thu, 9 Aug 2018 14:43:46 +0200
> Thierry Reding <thierry.reding@gmail.com> wrote:
>
> > On Wed, Aug 01, 2018 at 07:32:02PM +0300, Aapo Vienamo wrote:
> > > Parse the pinctrl state and nvidia,only-1-8-v properties from the device
> > > tree. Validate the pinctrl and regulator configuration before unmasking
> > > UHS modes. Implement pad voltage state reconfiguration in the mmc
> > > start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
> > > and add set it for Tegra210 and Tegra186.
> > >
> > > The pad configuration is done in the mmc callback because the order of
> > > pad reconfiguration and sdhci voltage switch depend on the voltage to
> > > which the transition occurs.
> > >
> > > Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
> > > ---
> > > drivers/mmc/host/sdhci-tegra.c | 138 ++++++++++++++++++++++++++++++++++++++---
> > > 1 file changed, 131 insertions(+), 7 deletions(-)
> > >
> > > diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> > > index ddf00166..7d98455 100644
> > > --- a/drivers/mmc/host/sdhci-tegra.c
> > > +++ b/drivers/mmc/host/sdhci-tegra.c
> > > @@ -21,6 +21,8 @@
> > > #include <linux/io.h>
> > > #include <linux/of.h>
> > > #include <linux/of_device.h>
> > > +#include <linux/pinctrl/consumer.h>
> > > +#include <linux/regulator/consumer.h>
> > > #include <linux/reset.h>
> > > #include <linux/mmc/card.h>
> > > #include <linux/mmc/host.h>
> > > @@ -55,6 +57,7 @@
> > > #define NVQUIRK_ENABLE_SDR104 BIT(4)
> > > #define NVQUIRK_ENABLE_DDR50 BIT(5)
> > > #define NVQUIRK_HAS_PADCALIB BIT(6)
> > > +#define NVQUIRK_NEEDS_PAD_CONTROL BIT(7)
> > >
> > > struct sdhci_tegra_soc_data {
> > > const struct sdhci_pltfm_data *pdata;
> > > @@ -66,8 +69,12 @@ struct sdhci_tegra {
> > > struct gpio_desc *power_gpio;
> > > bool ddr_signaling;
> > > bool pad_calib_required;
> > > + bool pad_control_available;
> > >
> > > struct reset_control *rst;
> > > + struct pinctrl *pinctrl_sdmmc;
> > > + struct pinctrl_state *pinctrl_state_3v3;
> > > + struct pinctrl_state *pinctrl_state_1v8;
> > > };
> > >
> > > static u16 tegra_sdhci_readw(struct sdhci_host *host, int reg)
> > > @@ -138,12 +145,46 @@ static unsigned int tegra_sdhci_get_ro(struct sdhci_host *host)
> > > return mmc_gpio_get_ro(host->mmc);
> > > }
> > >
> > > +static bool tegra_sdhci_is_pad_and_regulator_valid(struct sdhci_host *host)
> > > +{
> > > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > > + struct sdhci_tegra *tegra_host = sdhci_pltfm_priv(pltfm_host);
> > > + int has_1v8, has_3v3;
> >
> > Can these be boolean?
>
> In some cases regulator_is_supported_voltage() can return a negative
> error code.

Okay, that's fine then.

Thierry
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-08-09 15:15    [W:0.105 / U:48.580 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site