lkml.org 
[lkml]   [2018]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v3 2/2] tty/serial: atmel: add ISO7816 support
From
Date
Hi !

On 07/08/2018 15:00, Ludovic Desroches wrote:
> From: Nicolas Ferre <nicolas.ferre@microchip.com>
>
> When mode is set in atmel_config_iso7816() we backup last RS232 mode
> for coming back to this mode if requested.
> Also allow setup of T=0 and T=1 parameter and basic support in set_termios
> function as well.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
> [ludovic.desroches@microchip.com: rebase, add check on fidi ratio, checkpatch fixes]
> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
> ---
> drivers/tty/serial/atmel_serial.c | 211 +++++++++++++++++++++++++++++++++++---
> drivers/tty/serial/atmel_serial.h | 6 +-
> 2 files changed, 201 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 8e4428725848..4a7ec44b0ace 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -34,6 +34,7 @@
> #include <linux/suspend.h>
> #include <linux/mm.h>
>
> +#include <asm/div64.h>
> #include <asm/io.h>
> #include <asm/ioctls.h>
>
> @@ -83,6 +84,11 @@ static void atmel_stop_rx(struct uart_port *port);
>
> #define ATMEL_ISR_PASS_LIMIT 256
>
> +struct atmel_uart_pdata {
> + unsigned int fidi_min;
> + unsigned int fidi_max;
> +};
> +
> struct atmel_dma_buffer {
> unsigned char *buf;
> dma_addr_t dma_addr;
> @@ -114,6 +120,7 @@ struct atmel_uart_char {
> */
> struct atmel_uart_port {
> struct uart_port uart; /* uart */
> + const struct atmel_uart_pdata *pdata; /* SoC specific parameters */
> struct clk *clk; /* uart clock */
> int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
> u32 backup_imr; /* IMR saved during suspend */
> @@ -147,6 +154,8 @@ struct atmel_uart_port {
> struct circ_buf rx_ring;
>
> struct mctrl_gpios *gpios;
> + u32 backup_mode; /* MR saved during iso7816 operations */
> + u32 backup_brgr; /* BRGR saved during iso7816 operations */
> unsigned int tx_done_mask;
> u32 fifo_size;
> u32 rts_high;
> @@ -192,10 +201,34 @@ static struct console atmel_console;
> #endif
>
> #if defined(CONFIG_OF)
> +static struct atmel_uart_pdata at91rm9200_pdata = {
> + .fidi_min = 1,
> + .fidi_max = 2047,
> +};
> +
> +static struct atmel_uart_pdata at91sam9260_pdata = {
> + .fidi_min = 1,
> + .fidi_max = 2047,
> +};
> +
> +static struct atmel_uart_pdata sama5d3_pdata = {
> + .fidi_min = 3,
> + .fidi_max = 65535,
Are you sure this is for sama5d3 ?
From the datasheets I have, 65535 is for sama5d4/sama5d2
And also, you'll have to s/atmel,at91sam9260-usart/atmel,sama5d2-usart/g
in sama5d{2,4}.dtsi

But I wonder if it could be detected via ATMEL_US_VERSION instead ?


> +};
> +
> static const struct of_device_id atmel_serial_dt_ids[] = {
> - { .compatible = "atmel,at91rm9200-usart" },
> - { .compatible = "atmel,at91sam9260-usart" },
> - { /* sentinel */ }
> + {
> + .compatible = "atmel,at91rm9200-usart",
> + .data = &at91rm9200_pdata,
> + }, {
> + .compatible = "atmel,at91sam9260-usart",
> + .data = &at91sam9260_pdata,
> + }, {
> + .compatible = "atmel,sama5d3-usart",
> + .data = &sama5d3_pdata,
> + }, {
> + /* sentinel */
> + }
> };
> #endif
>
> @@ -362,6 +395,127 @@ static int atmel_config_rs485(struct uart_port *port,
> return 0;
> }
>
> +static unsigned int atmel_calc_cd(struct uart_port *port,
> + struct serial_iso7816 *iso7816conf)
> +{
> + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> + unsigned int cd;
> + u64 mck_rate;
> +
> + mck_rate = (u64)clk_get_rate(atmel_port->clk);
> + do_div(mck_rate, iso7816conf->clk);
> + cd = mck_rate;
> + return cd;
> +}
> +
> +static unsigned int atmel_calc_fidi(struct uart_port *port,
> + struct serial_iso7816 *iso7816conf)
> +{
> + u64 fidi = 0;
> +
> + if (iso7816conf->sc_fi && iso7816conf->sc_di) {
> + fidi = (u64)iso7816conf->sc_fi;
> + do_div(fidi, iso7816conf->sc_di);
> + }
> + return (u32)fidi;
> +}
> +
> +/* Enable or disable the iso7816 support */
> +/* Called with interrupts disabled */
> +static int atmel_config_iso7816(struct uart_port *port,
> + struct serial_iso7816 *iso7816conf)
> +{
> + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> + unsigned int mode;
> + unsigned int cd, fidi;
> + int ret = 0;
> +
> + /* Disable interrupts */
> + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
> +
> + mode = atmel_uart_readl(port, ATMEL_US_MR);
> +
> + if (iso7816conf->flags & SER_ISO7816_ENABLED) {
> + mode &= ~ATMEL_US_USMODE;
> +
> + if (iso7816conf->tg > 255) {
> + dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n");
> + memset(iso7816conf, 0, sizeof(struct serial_iso7816));
> + ret = -EINVAL;
> + goto err_out;
> + }
> +
> + if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
> + == SER_ISO7816_T(0)) {
> + mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK;
> + } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
> + == SER_ISO7816_T(1)) {
> + mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK;
> + } else {
> + dev_err(port->dev, "ISO7816: Type not supported\n");
> + memset(iso7816conf, 0, sizeof(struct serial_iso7816));
> + ret = -EINVAL;
> + goto err_out;
> + }
> +
> + mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR);
> +
> + /* select mck clock, and output */
> + mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
> + /* set parity for normal/inverse mode + max iterations */
> + mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3);
> +
> + cd = atmel_calc_cd(port, iso7816conf);
> + fidi = atmel_calc_fidi(port, iso7816conf);
> + if (fidi == 0) {
> + dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n");
> + } else if (fidi < atmel_port->pdata->fidi_min
> + || fidi > atmel_port->pdata->fidi_max) {
> + dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi);
> + memset(iso7816conf, 0, sizeof(struct serial_iso7816));
> + ret = -EINVAL;
> + goto err_out;
> + }
> +
> + if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) {
> + /* port not yet in iso7816 mode: store configuration */
> + atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR);
> + atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
> + }
> +
> + atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg);
> + atmel_uart_writel(port, ATMEL_US_BRGR, cd);
> + atmel_uart_writel(port, ATMEL_US_FIDIR, fidi);
> +
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN);
> + atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION;
> + } else {
> + dev_dbg(port->dev, "Setting UART back to RS232\n");
> + /* back to last RS232 settings */
> + mode = atmel_port->backup_mode;
> + memset(iso7816conf, 0, sizeof(struct serial_iso7816));
> + atmel_uart_writel(port, ATMEL_US_TTGR, 0);
> + atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr);
> + atmel_uart_writel(port, ATMEL_US_FIDIR, 0x174);
> +
> + if (atmel_use_pdc_tx(port))
> + atmel_port->tx_done_mask = ATMEL_US_ENDTX |
> + ATMEL_US_TXBUFE;
> + else
> + atmel_port->tx_done_mask = ATMEL_US_TXRDY;
> + }
> +
> + port->iso7816 = *iso7816conf;
> +
> + atmel_uart_writel(port, ATMEL_US_MR, mode);
> +
> +err_out:
> + /* Enable interrupts */
> + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
> +
> + return ret;
> +}
> +
> /*
> * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
> */
> @@ -481,8 +635,9 @@ static void atmel_stop_tx(struct uart_port *port)
> /* Disable interrupts */
> atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
>
> - if ((port->rs485.flags & SER_RS485_ENABLED) &&
> - !(port->rs485.flags & SER_RS485_RX_DURING_TX))
> + if (((port->rs485.flags & SER_RS485_ENABLED) &&
> + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> + port->iso7816.flags & SER_ISO7816_ENABLED)
> atmel_start_rx(port);
> }
>
> @@ -500,8 +655,9 @@ static void atmel_start_tx(struct uart_port *port)
> return;
>
> if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
> - if ((port->rs485.flags & SER_RS485_ENABLED) &&
> - !(port->rs485.flags & SER_RS485_RX_DURING_TX))
> + if (((port->rs485.flags & SER_RS485_ENABLED) &&
> + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> + port->iso7816.flags & SER_ISO7816_ENABLED)
> atmel_stop_rx(port);
>
> if (atmel_use_pdc_tx(port))
> @@ -799,8 +955,9 @@ static void atmel_complete_tx_dma(void *arg)
> */
> if (!uart_circ_empty(xmit))
> atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
> - else if ((port->rs485.flags & SER_RS485_ENABLED) &&
> - !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
> + else if (((port->rs485.flags & SER_RS485_ENABLED) &&
> + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> + port->iso7816.flags & SER_ISO7816_ENABLED) {
> /* DMA done, stop TX, start RX for RS485 */
> atmel_start_rx(port);
> }
> @@ -1281,6 +1438,9 @@ atmel_handle_status(struct uart_port *port, unsigned int pending,
> wake_up_interruptible(&port->state->port.delta_msr_wait);
> }
> }
> +
> + if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION))
> + dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending);
> }
>
> /*
> @@ -1373,8 +1533,9 @@ static void atmel_tx_pdc(struct uart_port *port)
> atmel_uart_writel(port, ATMEL_US_IER,
> atmel_port->tx_done_mask);
> } else {
> - if ((port->rs485.flags & SER_RS485_ENABLED) &&
> - !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
> + if (((port->rs485.flags & SER_RS485_ENABLED) &&
> + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> + port->iso7816.flags & SER_ISO7816_ENABLED) {
> /* DMA done, stop TX, start RX for RS485 */
> atmel_start_rx(port);
> }
> @@ -2099,6 +2260,17 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> atmel_uart_writel(port, ATMEL_US_TTGR,
> port->rs485.delay_rts_after_send);
> mode |= ATMEL_US_USMODE_RS485;
> + } else if (port->iso7816.flags & SER_ISO7816_ENABLED) {
> + atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg);
> + /* select mck clock, and output */
> + mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
> + /* set max iterations */
> + mode |= ATMEL_US_MAX_ITER(3);
> + if ((port->iso7816.flags & SER_ISO7816_T_PARAM)
> + == SER_ISO7816_T(0))
> + mode |= ATMEL_US_USMODE_ISO7816_T0;
> + else
> + mode |= ATMEL_US_USMODE_ISO7816_T1;
> } else if (termios->c_cflag & CRTSCTS) {
> /* RS232 with hardware handshake (RTS/CTS) */
> if (atmel_use_fifo(port) &&
> @@ -2175,7 +2347,8 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> }
> quot = cd | fp << ATMEL_US_FP_OFFSET;
>
> - atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> + if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
> + atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
> atmel_port->tx_stopped = false;
> @@ -2355,6 +2528,7 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
> port->mapbase = pdev->resource[0].start;
> port->irq = pdev->resource[1].start;
> port->rs485_config = atmel_config_rs485;
> + port->iso7816_config = atmel_config_iso7816;
> port->membase = NULL;
>
> memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
> @@ -2378,8 +2552,12 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
> /* only enable clock when USART is in use */
> }
>
> - /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
> - if (port->rs485.flags & SER_RS485_ENABLED)
> + /*
> + * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or
> + * ENDTX|TXBUFE
> + */
> + if (port->rs485.flags & SER_RS485_ENABLED ||
> + port->iso7816.flags & SER_ISO7816_ENABLED)
> atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
> else if (atmel_use_pdc_tx(port)) {
> port->fifosize = PDC_BUFFER_SIZE;
> @@ -2719,6 +2897,11 @@ static int atmel_serial_probe(struct platform_device *pdev)
> }
>
> atmel_port = &atmel_ports[ret];
> + atmel_port->pdata = of_device_get_match_data(&pdev->dev);
> + if (!atmel_port->pdata) {
> + ret = -EINVAL;
> + goto err;
> + }
> atmel_port->backup_imr = 0;
> atmel_port->uart.line = ret;
> atmel_serial_probe_fifos(atmel_port, pdev);
> diff --git a/drivers/tty/serial/atmel_serial.h b/drivers/tty/serial/atmel_serial.h
> index ba3a2437cde4..6911177964ad 100644
> --- a/drivers/tty/serial/atmel_serial.h
> +++ b/drivers/tty/serial/atmel_serial.h
> @@ -78,7 +78,8 @@
> #define ATMEL_US_OVER BIT(19) /* Oversampling Mode */
> #define ATMEL_US_INACK BIT(20) /* Inhibit Non Acknowledge */
> #define ATMEL_US_DSNACK BIT(21) /* Disable Successive NACK */
> -#define ATMEL_US_MAX_ITER GENMASK(26, 24) /* Max Iterations */
> +#define ATMEL_US_MAX_ITER_MASK GENMASK(26, 24) /* Max Iterations */
> +#define ATMEL_US_MAX_ITER(n) (((n) << 24) & ATMEL_US_MAX_ITER_MASK)
> #define ATMEL_US_FILTER BIT(28) /* Infrared Receive Line Filter */
>
> #define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
> @@ -124,7 +125,8 @@
> #define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
> #define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */
>
> -#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
> +#define ATMEL_US_FIDIR 0x40 /* FI DI Ratio Register */
> +#define ATMEL_US_FIDI GENMASK(15, 0) /* FIDI ratio */
> #define ATMEL_US_NER 0x44 /* Number of Errors Register */
> #define ATMEL_US_IF 0x4c /* IrDA Filter Register */
>
>
Thanks !

\
 
 \ /
  Last update: 2018-08-09 10:47    [W:0.098 / U:7.512 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site