lkml.org 
[lkml]   [2018]   [Aug]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH resend] [media] uvcvideo: zero seq number when disabling stream
Date
Hi Hans,

(CC'ing the linux-usb mailing list)

On Thursday, 19 October 2017 15:03:34 EEST Laurent Pinchart wrote:
> On Thursday, 19 October 2017 10:23:06 EEST Hans Yang wrote:
> > On 2017年10月18日 16:52, Guennadi Liakhovetski wrote:
> >> On Mon, 16 Oct 2017, Laurent Pinchart wrote:
> >>> On Friday, 15 September 2017 09:27:51 EEST Hans Yang wrote:
> >>>> For bulk-based devices, when disabling the video stream,
> >>>> in addition to issue CLEAR_FEATURE(HALT), it is better to set
> >>>> alternate setting 0 as well or the sequnce number in host
> >>>> side will probably not reset to zero.
> >>>
> >>> The USB 2.0 specificatin states in the description of the SET_INTERFACE
> >>> request that "If a device only supports a default setting for the
> >>> specified interface, then a STALL may be returned in the Status stage
> >>> of the request".
> >>>
> >>> The Linux implementation of usb_set_interface() deals with this by
> >>> handling STALL conditions and manually clearing HALT for all endpoints
> >>> in the interface, but I'm still concerned that this change could break
> >>> existing bulk- based cameras. Do you know what other operating systems
> >>> do when disabling the stream on bulk cameras ? According to a comment
> >>> in the driver Windows calls CLEAR_FEATURE(HALT), but the situation
> >>> might have changed since that was tested.
> >
> > Sorry I did not mention that it is about SS bulk-based cameras using
> > sequence number technique.
> >
> > From my observations, invoking usb_clear_halt() will reset the endpoint
> > in the device side via CLEAR_FEATURE(HALT)
> > and reset the sequence number as well; however usb_reset_endpoint() does
> > not reset the host side endpoint with xhci driver,
> > then the sequence number will mismatch in next time stream enable.
> > I can always observe this through a bus analyzer on Linux implementation
> > whatever X86 or ARM based.
> > This is not observed on the Windows.

Do your USB analyser traces show whether Windows sends a SET_INTERFACE(0)
request when stopping the stream for bulk-based devices ?

> According to the USB 3.0 specification, section 9.4.5 ("Get Status"),
>
> "Regardless of whether an endpoint has the Halt feature set, a
> ClearFeature(ENDPOINT_HALT) request always results in the data sequence
> being reinitialized to zero, and if Streams are enabled, the Stream State
> Machine shall be reinitialized to the Disabled state."
>
> If Linux doesn't reset the sequence number when issuing a
> CLEAR_FEATURE(HALT), isn't it a Linux USB stack bug that should be fixed in
> the USB core ?

Do you have any update on whether you would consider this to be a Linux USB
stack issue or a uvcvideo driver issue ?

> >>> Guennadi, how do your bulk-based cameras handle this ?
> >>
> >> I don't know what design decisions are implemented there, but I tested a
> >> couple of cameras for sending a STREAMOFF after a few captured buffers,
> >> sleeping for a couple of seconds, requeuing buffers, sending STREAMON
> >> and capturing a few more - that seems to have worked. "Seems" because I
> >> only used a modified version of capture-example, I haven't checked
> >> buffer contents.
> >>
> >> BTW, Hans, may I ask - what cameras did you use?
> >
> > I have three SS bulk-based cameras as follows:
> > e-con Systems See3CAM_CU130 (2560:c1d0)
> > Leopard ZED (2b03:f580)
> > Intel(R) RealSense(TM) Camera SR300 (8086:0aa5)
> >
> > I can observe the same issue on all above;
> > besides, to reproduce issue do not let the camera enter suspend because
> > it will *help* to reset the sequence number through usb_set_interface(0).
> >
> >>>> Then in next time video stream start, the device will expect
> >>>> host starts packet from 0 sequence number but host actually
> >>>> continue the sequence number from last transaction and this
> >>>> causes transaction errors.
> >>>
> >>> Do you mean the DATA0/DATA1 toggle ? Why does the host continue
> >>> toggling the PID from the last transation ? The usb_clear_halt()
> >>> function calls usb_reset_endpoint() which should reset the DATA PID
> >>> toggle.
> >>>
> >>>> This commit fixes this by adding set alternate setting 0 back
> >>>> as what isoch-based devices do.
> >>>>
> >>>> Below error message will also be eliminated for some devices:
> >>>> uvcvideo: Non-zero status (-71) in video completion handler.
> >>>>
> >>>> Signed-off-by: Hans Yang <hansy@nvidia.com>
> >>>> ---
> >>>>
> >>>> drivers/media/usb/uvc/uvc_video.c | 5 ++---
> >>>> 1 file changed, 2 insertions(+), 3 deletions(-)
> >>>>
> >>>> diff --git a/drivers/media/usb/uvc/uvc_video.c
> >>>> b/drivers/media/usb/uvc/uvc_video.c index fb86d6af398d..ad80c2a6da6a
> >>>> 100644
> >>>> --- a/drivers/media/usb/uvc/uvc_video.c
> >>>> +++ b/drivers/media/usb/uvc/uvc_video.c
> >>>> @@ -1862,10 +1862,9 @@ int uvc_video_enable(struct uvc_streaming
> >>>> *stream, int enable)
> >>>> if (!enable) {
> >>>> uvc_uninit_video(stream, 1);
> >>>>
> >>>> - if (stream->intf->num_altsetting > 1) {
> >>>> - usb_set_interface(stream->dev->udev,
> >>>> + usb_set_interface(stream->dev->udev,
> >>>> stream->intfnum, 0);
> >>>> - } else {
> >>>> + if (stream->intf->num_altsetting == 1) {
> >>>> /* UVC doesn't specify how to inform a bulk-based device
> >>>> * when the video stream is stopped. Windows sends a
> >>>> * CLEAR_FEATURE(HALT) request to the video streaming

--
Regards,

Laurent Pinchart



\
 
 \ /
  Last update: 2018-08-07 00:13    [W:0.053 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site