lkml.org 
[lkml]   [2018]   [Aug]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/5] arm: dts: qcom: Add pcie nodes for ipq8064
Date
Adding the pcie nodes and pins.

Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
arch/arm/boot/dts/qcom-ipq8064.dtsi | 182 ++++++++++++++++++++++++++++++++++++
1 file changed, 182 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 70790ac..e02d588 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -2,8 +2,11 @@
/dts-v1/;

#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>

@@ -114,6 +117,33 @@
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+
+ pcie0_pins: pcie0_pinmux {
+ mux {
+ pins = "gpio3";
+ function = "pcie1_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ pcie1_pins: pcie1_pinmux {
+ mux {
+ pins = "gpio48";
+ function = "pcie2_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ pcie2_pins: pcie2_pinmux {
+ mux {
+ pins = "gpio63";
+ function = "pcie3_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
};

intc: interrupt-controller@2000000 {
@@ -373,5 +403,157 @@
#reset-cells = <1>;
};

+ pcie0: pci@1b500000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b500000 0x1000
+ 0x1b502000 0x80
+ 0x1b600000 0x100
+ 0x0ff00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_A_CLK>,
+ <&gcc PCIE_H_CLK>,
+ <&gcc PCIE_PHY_CLK>,
+ <&gcc PCIE_AUX_CLK>,
+ <&gcc PCIE_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_ACLK_RESET>,
+ <&gcc PCIE_HCLK_RESET>,
+ <&gcc PCIE_POR_RESET>,
+ <&gcc PCIE_PCI_RESET>,
+ <&gcc PCIE_PHY_RESET>,
+ <&gcc PCIE_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+
+ status = "disabled";
+ perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ };
+
+ pcie1: pci@1b700000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b700000 0x1000
+ 0x1b702000 0x80
+ 0x1b800000 0x100
+ 0x31f00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_1_A_CLK>,
+ <&gcc PCIE_1_H_CLK>,
+ <&gcc PCIE_1_PHY_CLK>,
+ <&gcc PCIE_1_AUX_CLK>,
+ <&gcc PCIE_1_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_1_ACLK_RESET>,
+ <&gcc PCIE_1_HCLK_RESET>,
+ <&gcc PCIE_1_POR_RESET>,
+ <&gcc PCIE_1_PCI_RESET>,
+ <&gcc PCIE_1_PHY_RESET>,
+ <&gcc PCIE_1_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+
+ status = "disabled";
+ perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ };
+
+ pcie2: pci@1b900000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b900000 0x1000
+ 0x1b902000 0x80
+ 0x1ba00000 0x100
+ 0x35f00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_2_A_CLK>,
+ <&gcc PCIE_2_H_CLK>,
+ <&gcc PCIE_2_PHY_CLK>,
+ <&gcc PCIE_2_AUX_CLK>,
+ <&gcc PCIE_2_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_2_ACLK_RESET>,
+ <&gcc PCIE_2_HCLK_RESET>,
+ <&gcc PCIE_2_POR_RESET>,
+ <&gcc PCIE_2_PCI_RESET>,
+ <&gcc PCIE_2_PHY_RESET>,
+ <&gcc PCIE_2_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie2_pins>;
+ pinctrl-names = "default";
+
+ status = "disabled";
+ perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
+ };
};
};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
\
 
 \ /
  Last update: 2018-08-03 16:12    [W:0.093 / U:0.640 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site