lkml.org 
[lkml]   [2018]   [Jul]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/3] mmc: tegra: prevent ACMD23 on Tegra 3
On 26.07.2018 15:56, Peter Geis wrote:
> On 07/12/2018 03:39 AM, Stefan Agner wrote:
>> It seems that SD3.0 advertisement needs to be set for higher eMMC
>> speed modes (namely DDR52) as well. The TRM states that the SD3.0
>> advertisement bit should be set for all controller instances, even
>> for those not supporting UHS-I mode...
>>
>> When specifying vqmmc-supply as a fixed 1.8V regulator on a Tegra
>> SD/MMC instance which is connected to a eMMC device, the stack
>> enables SD3.0. However, enabling it has consequences: If SDHCI 3.0
>> support is advertised the stack enables Auto-CMD23. Unfortunately
>> Auto-CMD23 seems not to work well with Tegra 3 currently. It leads
>> to regular warnings:
>> mmc2: Got command interrupt 0x00010000 even though no command operation was in progress.
>>
>> It is not entirely clear why those errors happens. It seems that
>> a Linux 3.1 based downstream kernel which has Auto-CMD23 support
>> does not show those warnings.
>>
>> Use quirk SDHCI_QUIRK2_ACMD23_BROKEN to prevent Auto-CMD23 being
>> used for now. With this the eMMC works stable on high-speed mode
>> while still announcing SD3.0.
>>
>> This allows to use mmc-ddr-1_8v to enables DDR52 mode. In DDR52
>> mode read speed improves from about 42MiB/s to 72MiB/s on an
>> Apalis T30.
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>> drivers/mmc/host/sdhci-tegra.c | 10 +++++++++-
>> 1 file changed, 9 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
>> index 888a1ad511db..11c0b2069c7c 100644
>> --- a/drivers/mmc/host/sdhci-tegra.c
>> +++ b/drivers/mmc/host/sdhci-tegra.c
>> @@ -336,7 +336,15 @@ static const struct sdhci_pltfm_data sdhci_tegra30_pdata = {
>> SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC |
>> SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
>> .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
>> - SDHCI_QUIRK2_BROKEN_HS200,
>> + SDHCI_QUIRK2_BROKEN_HS200 |
>> + /*
>> + * Auto-CMD23 leads to "Got command interrupt 0x00010000 even
>> + * though no command operation was in progress."
>> + *
>> + * The exact reason is unknown, as the same hardware seems
>> + * to support Auto CMD23 on a downstream 3.1 kernel.
>> + */
>> + SDHCI_QUIRK2_ACMD23_BROKEN,
>> .ops = &tegra_sdhci_ops,
>> };
>>
>
> I finally got around to testing this on the Ouya (Tegra 3).

Thanks for testing!

>
> I found that the "Got command interrupt 0x00010000 even though no
> command operation was in progress." error occurred when the interface
> is unstable.
> I've had a lot of problems with sdmmc4 stability on the Ouya above 34
> Mhz, probably due to the fact that they are using the internal cmd and
> clock pull-up resistors, against the TRM's instruction.
> At 39Mhz, I saw the error this patch corrects.
> With the patch, the error went away, but the interface is still
> unstable under load.

How does this instability manifest exactly?

>
> Lowering down to 32Mhz, without the patch there are no errors.

So the patch does not make it less stable right?

--
Stefan

\
 
 \ /
  Last update: 2018-07-26 16:48    [W:0.155 / U:0.412 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site