lkml.org 
[lkml]   [2018]   [Jul]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/3] pinctrl: qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant
Date
If you do this on an sdm845 board:
grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups

...it looks like nonsense. For every pin you see listed:
input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...

That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE. Oops.

Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---

drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 32 ++++++++++++++++++------
1 file changed, 24 insertions(+), 8 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index 3e66e0d10010..cf82db78e69e 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -390,31 +390,47 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,

switch (param) {
case PIN_CONFIG_DRIVE_PUSH_PULL:
- arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS;
+ if (pad->buffer_type != PMIC_GPIO_OUT_BUF_CMOS)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
- arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+ if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_DRIVE_OPEN_SOURCE:
- arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+ if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_BIAS_PULL_DOWN:
- arg = pad->pullup == PMIC_GPIO_PULL_DOWN;
+ if (pad->pullup != PMIC_GPIO_PULL_DOWN)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_BIAS_DISABLE:
- arg = pad->pullup = PMIC_GPIO_PULL_DISABLE;
+ if (pad->pullup != PMIC_GPIO_PULL_DISABLE)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_BIAS_PULL_UP:
- arg = pad->pullup == PMIC_GPIO_PULL_UP_30;
+ if (pad->pullup != PMIC_GPIO_PULL_UP_30)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
- arg = !pad->is_enabled;
+ if (pad->is_enabled)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_POWER_SOURCE:
arg = pad->power_source;
break;
case PIN_CONFIG_INPUT_ENABLE:
- arg = pad->input_enabled;
+ if (!pad->input_enabled)
+ return -EINVAL;
+ arg = 1;
break;
case PIN_CONFIG_OUTPUT:
arg = pad->out_value;
--
2.18.0.399.gad0ab374a1-goog
\
 
 \ /
  Last update: 2018-07-03 01:01    [W:0.084 / U:0.884 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site