lkml.org 
[lkml]   [2018]   [Jul]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v7 2/7] thermal: tsens: Add support to split up register address space into two
On Wed, Jul 18, 2018 at 4:59 AM Matthias Kaehlcke <mka@chromium.org> wrote:
>
> On Thu, Jul 12, 2018 at 02:09:03PM +0530, Amit Kucheria wrote:
> > There are two banks of registers for v2 TSENS IPs: SROT and TM. On older
> > SoCs these were contiguous, leading to DTs mapping them as one register
> > address space of size 0x2000. In newer SoCs, these two banks are not
> > contiguous anymore.
> >
> > Add logic to init_common() to differentiate between old and new DTs and
> > adjust associated offsets for the TM register bank so that the old DTs will
> > continue to function correctly.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Tested-by: Matthias Kaehlcke <mka@chromium.org>
> > ---
> > drivers/thermal/qcom/tsens-8996.c | 4 ++--
> > drivers/thermal/qcom/tsens-common.c | 12 ++++++++++++
> > drivers/thermal/qcom/tsens.h | 1 +
> > 3 files changed, 15 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/thermal/qcom/tsens-8996.c b/drivers/thermal/qcom/tsens-8996.c
> > index e1f7781..3e60cec 100644
> > --- a/drivers/thermal/qcom/tsens-8996.c
> > +++ b/drivers/thermal/qcom/tsens-8996.c
> > @@ -16,7 +16,7 @@
> > #include <linux/regmap.h>
> > #include "tsens.h"
> >
> > -#define STATUS_OFFSET 0x10a0
> > +#define STATUS_OFFSET 0xa0
> > #define LAST_TEMP_MASK 0xfff
> > #define STATUS_VALID_BIT BIT(21)
> > #define CODE_SIGN_BIT BIT(11)
> > @@ -28,7 +28,7 @@ static int get_temp_8996(struct tsens_device *tmdev, int id, int *temp)
> > unsigned int sensor_addr;
> > int last_temp = 0, last_temp2 = 0, last_temp3 = 0, ret;
> >
> > - sensor_addr = STATUS_OFFSET + s->hw_id * 4;
> > + sensor_addr = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * 4;
> > ret = regmap_read(tmdev->map, sensor_addr, &code);
> > if (ret)
> > return ret;
> > diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> > index b1449ad..c22dc18 100644
> > --- a/drivers/thermal/qcom/tsens-common.c
> > +++ b/drivers/thermal/qcom/tsens-common.c
> > @@ -16,6 +16,7 @@
> > #include <linux/io.h>
> > #include <linux/nvmem-consumer.h>
> > #include <linux/of_address.h>
> > +#include <linux/of_platform.h>
> > #include <linux/platform_device.h>
> > #include <linux/regmap.h>
> > #include "tsens.h"
> > @@ -126,11 +127,22 @@ static const struct regmap_config tsens_config = {
> > int __init init_common(struct tsens_device *tmdev)
> > {
> > void __iomem *base;
> > + struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
> >
> > + if (!op)
> > + return -EINVAL;
> > base = of_iomap(tmdev->dev->of_node, 0);
> > if (!base)
> > return -EINVAL;
> >
> > + /* The driver only uses the TM register address space for now */
> > + if (op->num_resources > 1) {
> > + tmdev->tm_offset = 0;
> > + } else {
> > + /* old DTs where SROT and TM were in a contiguous 2K block */
> > + tmdev->tm_offset = 0x1000;
> > + }
>
> nit: no curly braces for conditionals with a single statement. There
> is probably no need to respin just for this though.

Yeah, that was leftover from refactoring because I have an upcoming
patch that adds SROT mapping inside those braces. I'm about to post it
soon.

> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

\
 
 \ /
  Last update: 2018-07-18 05:43    [W:0.068 / U:1.508 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site