lkml.org 
[lkml]   [2018]   [Jul]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [linux-sunxi] [PATCH 2/2] ARM: sun8i: h3: add SY8113B regulator on Banana Pi M2 Zero board
From


于 2018年7月11日 GMT+08:00 下午10:15:41, Chen-Yu Tsai <wens@csie.org> 写到:
>Hi,
>
>On Wed, Jul 11, 2018 at 9:44 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
>> Banana Pi M2 Zero board has a SY8113B regulator, which is controlled
>via
>> GPIO and capable of outputing 1.1V when the PL1 GPIO is set to output
>0
>> or 1.1V when the PL6 GPIO is set to input or output 1, and the output
>is
>> the power supply of the ARM cores in H3 SoC.
>>
>> Add the device tree node of this regulator and set the cpu's
>cpu-supply
>> property to it.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> ---
>> .../dts/sun8i-h2-plus-bananapi-m2-zero.dts | 21
>+++++++++++++++++++
>> 1 file changed, 21 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> index eb61dcf32797..abc8dc750f4b 100644
>> --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> @@ -59,6 +59,23 @@
>> };
>> };
>>
>> + reg_vdd_cpux: vdd-cpux-regulator {
>> + compatible = "regulator-gpio";
>> + regulator-name = "vdd-cpux";
>> + regulator-type = "voltage";
>> + regulator-boot-on;
>> + regulator-always-on;
>> + regulator-min-microvolt = <1100000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-ramp-delay = <50>; /* 4ms */
>> +
>> + gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
>> + enable-active-high;
>> + gpios-states = <0x1>;
>> + states = <1100000 0x0
>
>So looking at the schematics with the resistor values, this calculates
>to roughly 1.108475 (0.6 * (1 + 10 / 11.8)) ...
>
>> + 1300000 0x1>;
>
>and this to 1.308475.

But I think it cannot reach such accuracy, because of the
error of component values and the error of the power voltage.

In addition, set it to a too accurate value may break the
common opp table.

>
>ChenYu
>
>> + };
>> +
>> wifi_pwrseq: wifi_pwrseq {
>> compatible = "mmc-pwrseq-simple";
>> pinctrl-names = "default";
>> @@ -66,6 +83,10 @@
>> };
>> };
>>
>> +&cpu0 {
>> + cpu-supply = <&reg_vdd_cpux>;
>> +};
>> +
>> &de {
>> status = "okay";
>> };
>> --
>> 2.17.1
>>
>> --
>> You received this message because you are subscribed to the Google
>Groups "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it,
>send an email to linux-sunxi+unsubscribe@googlegroups.com.
>> For more options, visit https://groups.google.com/d/optout.

\
 
 \ /
  Last update: 2018-07-11 16:20    [W:0.034 / U:8.036 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site