lkml.org 
[lkml]   [2018]   [Jun]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH v5 2/4] mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
Document devicetree bindings for ROHM BD71837 PMIC MFD.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
.../devicetree/bindings/mfd/rohm,bd71837-pmic.txt | 76 ++++++++++++++++++++++
1 file changed, 76 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt

diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
new file mode 100644
index 000000000000..ac2b66181f17
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
@@ -0,0 +1,76 @@
+* ROHM BD71837 Power Management Integrated Circuit bindings
+
+BD71837MWV is a programmable Power Management IC for powering single-core,
+dual-core, and quad-core SoC’s such as NXP-i.MX 8M. It is optimized for
+low BOM cost and compact solution footprint. It integrates 8 Buck
+egulators and 7 LDO’s to provide all the power rails required by the SoC and
+the commonly used peripherals.
+
+Required properties:
+ - compatible : Should be "rohm,bd71837".
+ - reg : I2C slave address.
+ - interrupt-parent : Phandle to the parent interrupt controller.
+ - interrupts : The interrupt line the device is connected to.
+ - regulators: : List of child nodes that specify the regulators
+ Please see ../regulator/rohm,bd71837-regulator.txt
+ - clock: : Please see ../clock/rohm,bd71837-clock.txt
+
+Optional properties:
+ - interrupt-controller : Marks the device node as an interrupt controller.
+ BD71837MWV can report different power state change
+ events to other drivers. Different events can be seen
+ as separate BD71837 domain interrupts.
+ The BD71837 driver only provides the infrastructure
+ for the IRQs. The users should write own driver to
+ convert the IRQ into the event they wish. The IRQ can
+ be used with the standard
+ request_irq/enable_irq/disable_irq API inside the
+ kernel.
+ - #interrupt-cells : The number of cells to describe an IRQ should be 1.
+ The value in cell is the IRQ number.
+ Meaningfull numbers are:
+ 0 => PMIC_STBY_REQ level change
+ 1 => PMIC_ON_REQ level change
+ 2 => WDOG_B level change
+ 3 => Power Button level change
+ 4 => Power Button Long Push
+ 5 => Power Button Short Push
+ 6 => SWRESET register is written 1
+
+Example:
+
+ pmic: pmic@4b {
+ compatible = "rohm,bd71837";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <29 GPIO_ACTIVE_LOW>;
+ interrupt-names = "irq";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+
+ regulators {
+ buck1: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ };
+ /* ... */
+ };
+ };
+
+ /* driver consuming PMIC interrupts */
+
+ my-power-button: power-button {
+ compatible = "foo";
+ interrupt-parent = <&pmic>;
+ interrupts = <3>, <4>, <5>;
+ interrupt-names = "pwrb", "pwrb-l", "pwrb-s";
+ /* ... */
+ };
+
--
2.14.3
\
 
 \ /
  Last update: 2018-06-04 15:21    [W:0.111 / U:13.788 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site