lkml.org 
[lkml]   [2018]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    Subject[PATCH v8 0/2] mfd/regulator/clk/input: bd71837: ROHM BD71837 PMIC driver
    Patch series adding support for ROHM BD71837 PMIC.

    BD71837 is a programmable Power Management IC for powering single-core,
    dual-core, and quad-core SoC’s such as NXP-i.MX 8M. It is optimized for
    low BOM cost and compact solution footprint. It integrates 8 buck
    regulators and 7 LDO’s to provide all the power rails required by the
    SoC and the commonly used peripherals.

    This is reduced set of patches containing only the MFD and devicetree
    bindings. Devicetree bindings patch (2) is not changed. The MFD patch
    enables alrady applied regulator part and power button support using
    gpio-keys. Clock and reset support will be sent as separate set of
    patches - possibly only after my vacations. Sorry for longish delay
    which will follow.

    Changelog v8
    - Dropped clk-bd71837 from series (will send later)
    - Patch 2 is unchanged.
    - Dropped bd718xx-pwrkey driver and used gpio_keys instead.
    - Added power-button short/long press duration configuratio to MFD
    - Cleaned MFD driver according to comments from Enric Balletbo Serra.
    (used devm, removed unnecessary header inclusions, removed redundant
    assignment, styling issues, allow building MFD part as module, fixed
    license mismatch).

    Changelog v7
    - patch 1: Cleaned MFD probe since MFD no longer directly reads DT
    properties.
    - patch 1/4: Moved power-key related definitions from powerkey patch (4)
    to MFD patch (1) so that powerkey can be applied independently
    - Patch 2 is unchanged.
    - patch 3: Added missing allocation check back to clk probe

    Changelog v6
    - Added power-key input driver
    Based on feedback from Rob Herring and Stephen Boyd
    - Added link to datasheet
    - Removed interrupt-controller from DT and fixed binding document
    - clk styling fixes
    - remove clkdev usage
    - add clk bindings to MFD documentation
    - removed clk binding document

    Changelog v5
    - dropped regulator patches which are already applied to Mark's tree
    Based on feedback from Rob Herring and Stephen Boyd
    - mfd bindings: explain why this can be interrupt-controller
    - mfd bindings: describe interrupts better
    - mfd bindings: require one cell interrupt specifier
    - mfd bindings: use generic node names in example
    - mfd driver: ack masked interrupt once at init
    - clk bindings: use generic node names in example
    - clk driver: use devm
    - clk driver: use of_clk_add_hw_provider
    - clk driver: change severity of print and how prints are emitted at
    probe error path.
    - clk driver: dropped forward declared functions
    - clk configs: drop unnecessary dependencies
    - clk driver: other styling issues
    - mfd/clk DT: drop clk node.

    Changelog v4
    - remove mutex from regulator state check as core prevents simultaneous
    accesses
    - allow voltage change for bucks 1 to 4 when regulator is enabled
    - fix indentiation problems
    - properly correct SPDX comments

    Changelog v3
    - kill unused variable
    - kill unused definitions
    - use REGMAP_IRQ_REG

    Changelog v2
    Based on feedback from Mark Brown
    - Squashed code and buildfile changes to same patch
    - Fixed some styling issues
    - Changed SPDX comments to CPP style
    - Error out if voltage is changed when regulator is enabled instead of
    Disabling the regulator for duration of change
    - Use devm_regulator_register
    - Remove compatible usage from regulators - use parent dev for config
    - Add a note about using regulator-boot-on for BUCK6 and 7
    - fixed warnings from kbuild test robot

    patch 1:
    MFD driver and definitions bringing interrupt support and
    enabling clk, regulator and input subsystems.
    patch 2:
    MFD driver DT bindings

    This patch series is based on for-mfd-next

    ---

    Matti Vaittinen (2):
    mfd: bd71837: mfd driver for ROHM BD71837 PMIC
    mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC

    .../devicetree/bindings/mfd/rohm,bd71837-pmic.txt | 67 ++++
    drivers/mfd/Kconfig | 13 +
    drivers/mfd/Makefile | 1 +
    drivers/mfd/bd71837.c | 220 ++++++++++++
    include/linux/mfd/bd71837.h | 391 +++++++++++++++++++++
    5 files changed, 692 insertions(+)
    create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
    create mode 100644 drivers/mfd/bd71837.c
    create mode 100644 include/linux/mfd/bd71837.h

    --
    2.14.3

    \
     
     \ /
      Last update: 2018-06-29 10:22    [W:2.567 / U:1.096 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site