lkml.org 
[lkml]   [2018]   [Jun]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v10 13/14] cpufreq: Add module to register cpufreq on Krait CPUs
The pvs refuse check is incorrect... With downstream it says it isn't
blown and that it is 11, which also happens on upstream if I import it's
efuse reading code from an older revision, or comment out the check.

Also, I'm still getting my issue about clocks above 2,147,483,647hz
however I think this may be related to the division in the hfpll driver
so I'll have a debug around there.

On Tue, Jun 19, 2018 at 07:15:24PM +0530, Sricharan R wrote:
> From: Stephen Boyd <sboyd@codeaurora.org>
>
> Register a cpufreq-generic device whenever we detect that a
> "qcom,krait" compatible CPU is present in DT.
>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> [Sricharan: updated to use dev_pm_opp_set_prop_name and
> nvmem apis]
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> [Thierry Escande: update to add support for opp-supported-hw]
> Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> ---
> [v10] updated to add support for opp-supported-hw given by
> Thierry Escande <thierry.escande@linaro.org>
>
> drivers/cpufreq/Kconfig.arm | 10 ++
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/cpufreq-dt-platdev.c | 5 +
> drivers/cpufreq/qcom-cpufreq.c | 201 +++++++++++++++++++++++++++++++++++
> 4 files changed, 217 insertions(+)
> create mode 100644 drivers/cpufreq/qcom-cpufreq.c
>
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 7f56fe5..87e5d8d 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -134,6 +134,16 @@ config ARM_OMAP2PLUS_CPUFREQ
> depends on ARCH_OMAP2PLUS
> default ARCH_OMAP2PLUS
>
> +config ARM_QCOM_CPUFREQ
> + bool "CPUfreq driver for the QCOM SoCs with KRAIT processors"
> + depends on ARCH_QCOM
> + select PM_OPP
> + help
> + This enables the CPUFreq driver for Qualcomm SoCs with
> + KRAIT processors.
> +
> + If in doubt, say N.
> +
> config ARM_S3C_CPUFREQ
> bool
> help
> diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
> index 8d24ade..c591e1e 100644
> --- a/drivers/cpufreq/Makefile
> +++ b/drivers/cpufreq/Makefile
> @@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o
> obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o
> obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o
> obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o
> +obj-$(CONFIG_ARM_QCOM_CPUFREQ) += qcom-cpufreq.o
> obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o
> obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o
> obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
> diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
> index 3b585e4..e2e9a99 100644
> --- a/drivers/cpufreq/cpufreq-dt-platdev.c
> +++ b/drivers/cpufreq/cpufreq-dt-platdev.c
> @@ -127,6 +127,11 @@
> { .compatible = "ti,am43", },
> { .compatible = "ti,dra7", },
>
> + { .compatible = "qcom,ipq8064", },
> + { .compatible = "qcom,apq8064", },
> + { .compatible = "qcom,msm8974", },
> + { .compatible = "qcom,msm8960", },
> +
> { }
> };
>
> diff --git a/drivers/cpufreq/qcom-cpufreq.c b/drivers/cpufreq/qcom-cpufreq.c
> new file mode 100644
> index 0000000..1d4ab54
> --- /dev/null
> +++ b/drivers/cpufreq/qcom-cpufreq.c
> @@ -0,0 +1,201 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (c) 2018, The Linux Foundation. All rights reserved.
> +
> +#include <linux/cpu.h>
> +#include <linux/module.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_opp.h>
> +#include <linux/slab.h>
> +
> +static void __init get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver,
> + struct nvmem_cell *pvs_nvmem, u8 *buf)
> +{
> + u32 pte_efuse;
> +
> + pte_efuse = *((u32 *)buf);
> +
> + *speed = pte_efuse & 0xf;
> + if (*speed == 0xf)
> + *speed = (pte_efuse >> 4) & 0xf;
> +
> + if (*speed == 0xf) {
> + *speed = 0;
> + pr_warn("Speed bin: Defaulting to %d\n", *speed);
> + } else {
> + pr_info("Speed bin: %d\n", *speed);
> + }
> +
> + *pvs = (pte_efuse >> 10) & 0x7;
> + if (*pvs == 0x7)
> + *pvs = (pte_efuse >> 13) & 0x7;
> +
> + if (*pvs == 0x7) {
> + *pvs = 0;
> + pr_warn("PVS bin: Defaulting to %d\n", *pvs);
> + } else {
> + pr_info("PVS bin: %d\n", *pvs);
> + }
> +
> + kfree(buf);
> +}
> +
> +static void __init get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver,
> + struct nvmem_cell *pvs_nvmem, u8 *buf)
> +{
> + u32 pte_efuse, redundant_sel;
> +
> + pte_efuse = *((u32 *)buf);
> + redundant_sel = (pte_efuse >> 24) & 0x7;
> + *speed = pte_efuse & 0x7;
> +
> + /* 4 bits of PVS are in efuse register bits 31, 8-6. */
> + *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7);
> + *pvs_ver = (pte_efuse >> 4) & 0x3;
> +
> + switch (redundant_sel) {
> + case 1:
> + *speed = (pte_efuse >> 27) & 0xf;
> + break;
> + case 2:
> + *pvs = (pte_efuse >> 27) & 0xf;
> + break;
> + }
> +
> + /* Check SPEED_BIN_BLOW_STATUS */
> + if (pte_efuse & BIT(3)) {
> + pr_info("Speed bin: %d\n", *speed);
> + } else {
> + pr_warn("Speed bin not set. Defaulting to 0!\n");
> + *speed = 0;
> + }
> +
> + /* Check PVS_BLOW_STATUS */
> + pte_efuse = *(((u32 *)buf) + 4);
> + if (pte_efuse) {
> + pr_info("PVS bin: %d\n", *pvs);
> + } else {
> + pr_warn("PVS bin not set. Defaulting to 0!\n");
> + *pvs = 0;
> + }
> +
> + pr_info("PVS version: %d\n", *pvs_ver);
> + kfree(buf);
> +}
> +
> +static int __init qcom_cpufreq_populate_opps(struct nvmem_cell *pvs_nvmem,
> + struct opp_table **tbl1,
> + struct opp_table **tbl2)
> +{
> + int speed = 0, pvs = 0, pvs_ver = 0, cpu, ret;
> + struct device *cpu_dev;
> + u8 *buf;
> + size_t len;
> + char pvs_name[] = "speedXX-pvsXX-vXX";
> + u32 hw_version;
> +
> + buf = nvmem_cell_read(pvs_nvmem, &len);
> + if (len == 4)
> + get_krait_bin_format_a(&speed, &pvs, &pvs_ver, pvs_nvmem, buf);
> + else if (len == 8)
> + get_krait_bin_format_b(&speed, &pvs, &pvs_ver, pvs_nvmem, buf);
> + else
> + pr_warn("Unable to read nvmem data. Defaulting to 0!\n");
> +
> + snprintf(pvs_name, sizeof(pvs_name), "speed%d-pvs%d-v%d",
> + speed, pvs, pvs_ver);
> +
> + hw_version = (1 << speed);
> +
> + for (cpu = 0; cpu < num_possible_cpus(); cpu++) {
> + cpu_dev = get_cpu_device(cpu);
> + if (!cpu_dev)
> + return -ENODEV;
> +
> + tbl1[cpu] = dev_pm_opp_set_prop_name(cpu_dev, pvs_name);
> + if (IS_ERR(tbl1[cpu])) {
> + ret = PTR_ERR(tbl1[cpu]);
> + tbl1[cpu] = 0;
> + pr_warn("failed to add OPP name %s\n", pvs_name);
> + return ret;
> + }
> +
> + tbl2[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, &hw_version,
> + 1);
> + if (IS_ERR(tbl2[cpu])) {
> + ret = PTR_ERR(tbl2[cpu]);
> + tbl2[cpu] = 0;
> + pr_warn("failed to set supported hw version\n");
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int __init qcom_cpufreq_driver_init(void)
> +{
> + struct platform_device *pdev;
> + struct device *cpu_dev;
> + struct device_node *np;
> + struct nvmem_cell *pvs_nvmem;
> + struct opp_table *tbl1[NR_CPUS] = { NULL }, *tbl2[NR_CPUS] = { NULL };
> + int ret, cpu = 0;
> +
> + cpu_dev = get_cpu_device(0);
> + if (!cpu_dev)
> + return -ENODEV;
> +
> + np = dev_pm_opp_of_get_opp_desc_node(cpu_dev);
> + if (!np)
> + return -ENOENT;
> +
> + if (!of_device_is_compatible(np, "operating-points-v2-krait-cpu")) {
> + ret = -ENOENT;
> + goto free_np;
> + }
> +
> + pvs_nvmem = of_nvmem_cell_get(np, NULL);
> + if (IS_ERR(pvs_nvmem)) {
> + dev_err(cpu_dev, "Could not get nvmem cell\n");
> + ret = PTR_ERR(pvs_nvmem);
> + goto free_np;
> + }
> +
> + ret = qcom_cpufreq_populate_opps(pvs_nvmem, tbl1, tbl2);
> + if (ret)
> + goto free_opp_name;
> +
> + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
> + if (IS_ERR(pdev)) {
> + ret = PTR_ERR(pdev);
> + goto free_opp_name;
> + }
> +
> + of_node_put(np);
> +
> + return 0;
> +
> +free_opp_name:
> + while (tbl1[cpu]) {
> + dev_pm_opp_put_prop_name(tbl1[cpu]);
> + cpu++;
> + }
> +
> + cpu = 0;
> + while (tbl2[cpu]) {
> + dev_pm_opp_put_supported_hw(tbl2[cpu]);
> + cpu++;
> + }
> +
> +free_np:
> + of_node_put(np);
> +
> + return ret;
> +}
> +late_initcall(qcom_cpufreq_driver_init);
> +
> +MODULE_DESCRIPTION("Qualcomm CPUfreq driver");
> +MODULE_AUTHOR("Stephen Boyd <sboyd@codeaurora.org>");
> +MODULE_LICENSE("GPL v2");
> --
> 1.9.1
>

\
 
 \ /
  Last update: 2018-06-19 17:31    [W:0.650 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site