lkml.org 
[lkml]   [2018]   [Jun]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: REGRESSION: "wlcore: sdio: allow pm to handle sdio power" breaks wifi on HiKey960
From
Date
Hi,

On 13/06/18 05:13, Tony Lindgren wrote:
> * John Stultz <john.stultz@linaro.org> [180612 22:15]:
>> Hey Folks,
>> I noticed with linus/master wifi wasn't coming up on HiKey960. I
>> bisected it down and it seems to be due to:
>>
>> 60f36637bbbd ("wlcore: sdio: allow pm to handle sdio power") and
>> 728a9dc61f13 ("wlcore: sdio: Fix flakey SDIO runtime PM handling")
>>
>> When wifi fails to load, the only useful error message I see is:
>> [ 8.466097] wl1271_sdio mmc1:0001:2: wl12xx_sdio_power_on: failed
>> to get_sync(-13)
>
> Sorry to hear about that.
>
>> Reverting those two changes gets wifi working again for me:
>> [ 8.754953] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
>> [ 8.761778] random: crng init done
>> [ 8.765185] random: 7 urandom warning(s) missed due to ratelimiting
>> [ 8.779149] wlcore: loaded
>> ...
>> [ 12.945903] wlcore: PHY firmware version: Rev 8.2.0.0.237
>> [ 13.058077] wlcore: firmware booted (Rev 8.9.0.0.70)
>>
>>
>> Any suggestions how to resolve this w/o a revert?
>
> Sounds like we need to ignore also -EACCES if runtime PM is
> disabled for MMC. Care to try and see if the patch below
> helps?
>

I don't use wifi with my board (I have an USB ethernet adapter), but I do
get the same error message as John.

Reverting the patches works and I do see wlan0 being brought up. Sadly,
applying your patch doesn't seem to fix the issue - and actually it seems
to freeze my board on first boot with this error:

[ 11.169127] wlcore: ERROR timeout waiting for the hardware to complete initialization

On second boot it finally comes to life, but issuing ifconfig freezes it again.

$ dmesg | grep wl
[ 5.922661] wl18xx_driver wl18xx.0.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
[ 5.933904] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2
[ 5.949158] wlcore: WARNING falling back to default config
[ 6.199806] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[ 6.210738] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
[ 6.221644] wlcore: WARNING This default nvs file can be removed from the file system
[ 6.235180] wlcore: loaded
[ 6.820146] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 7.280611] wlcore: PHY firmware version: Rev 8.2.0.0.236
[ 7.388339] wlcore: firmware booted (Rev 8.9.0.0.69)
[ 7.409610] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 7.417815] wlcore: down
[ 10.628867] wlcore: ERROR timeout waiting for the hardware to complete initialization


Seems like it's not getting powered on, which might be why those mmc_power_*
calls were in there originally ?

> Regards,
>
> Tony
>
> 8< ------------------------
> diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
> --- a/drivers/net/wireless/ti/wlcore/sdio.c
> +++ b/drivers/net/wireless/ti/wlcore/sdio.c
> @@ -155,7 +155,7 @@ static int wl12xx_sdio_power_on(struct wl12xx_sdio_glue *glue)
> struct mmc_card *card = func->card;
>
> ret = pm_runtime_get_sync(&card->dev);
> - if (ret < 0) {
> + if (ret < 0 && ret != -EACCES) {
> pm_runtime_put_noidle(&card->dev);
> dev_err(glue->dev, "%s: failed to get_sync(%d)\n",
> __func__, ret);
> @@ -182,7 +182,7 @@ static int wl12xx_sdio_power_off(struct wl12xx_sdio_glue *glue)
>
> /* Let runtime PM know the card is powered off */
> error = pm_runtime_put(&card->dev);
> - if (error < 0 && error != -EBUSY) {
> + if (error < 0 && error != -EBUSY && error != -EACCES) {
> dev_err(&card->dev, "%s failed: %i\n", __func__, error);
>
> return error;
>

\
 
 \ /
  Last update: 2018-06-13 16:43    [W:0.078 / U:0.212 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site