lkml.org 
[lkml]   [2018]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] arm64: allwinner: a64-amarula-relic: Enable AP6330 WiFi support
Date
Enable AP6330 WiFi/BT combo chip on Amarula A64-Relic board:
- WiFi SDIO interface is connected to MMC1
- WiFi WL-PMU-EN pin connected to gpio PL2: attach to mmc-pwrseq
- WiFi WL-WAKE-AP pin connected to gpio PL3
- 32kHz external oscillator gate clock from RTC

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
.../dts/allwinner/sun50i-a64-amarula-relic.dts | 37 ++++++++++++++++++++++
1 file changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index ce4a256ff086..a77b70ca88e3 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -21,12 +21,43 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */
+ };
};

&ehci0 {
status = "okay";
};

+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ /*
+ * Schematic shows both dldo4 and eldo1 connected for vcc-io-wifi, but
+ * dldo4 connection shows DNP(Do Not Populate) and eldo1 connected with
+ * 0Ohm register to vcc-io-wifi so eldo1 is used.
+ */
+ vqmmc-supply = <&reg_eldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* WL-WAKE-AP: PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
@@ -170,6 +201,12 @@
regulator-name = "vcc-rtc";
};

+&rtc {
+ clock-output-names = "rtc-osc32k", "rtc-osc32k-out";
+ clocks = <&osc32k>;
+ #clock-cells = <1>;
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
--
2.14.3
\
 
 \ /
  Last update: 2018-05-29 19:23    [W:0.038 / U:5.048 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site