lkml.org 
[lkml]   [2018]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Another NVMe failure, this time with AER info
Andrew wrote:
> A friend of mine has a brand new LG laptop that has intermittent NVMe
> failures. They mostly happen during a suspend/resume cycle
> (apparently during suspend, not resume). Unlike the earlier
> Dell/Samsung issue, the NVMe device isn't completely gone -- MMIO
> reads fail, but PCI configuration space is apparently still there:

> nvme nvme0: controller is down; will reset: CSTS=0xffffffff, PCI_STATUS=0x10

> and it comes with a nice AER dump:

> [12720.894411] pcieport 0000:00:1c.0: AER: Multiple Corrected error received: id=00e0
> [12720.909747] pcieport 0000:00:1c.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, id=00e0(Transmitter ID)
> [12720.909751] pcieport 0000:00:1c.0: device [8086:9d14] error status/mask=00001001/00002000
> [12720.909754] pcieport 0000:00:1c.0: [ 0] Receiver Error (First)
> [12720.909756] pcieport 0000:00:1c.0: [12] Replay Timer Timeout

I opened this bugzilla and attached the dmesg and lspci -vv output to
it: https://bugzilla.kernel.org/show_bug.cgi?id=199695

The root port at 00:1c.0 leads to the NVMe device at 01:00.0 (this is
nvme0):

00:1c.0 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #5 (rev f1) (prog-if 00 [Normal decode])
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express])
Subsystem: Samsung Electronics Co Ltd Device a801

We reported several corrected errors before the nvme timeout:

[12750.281158] nvme nvme0: controller is down; will reset: CSTS=0xffffffff, PCI_STATUS=0x10
[12750.297594] nvme nvme0: I/O 455 QID 2 timeout, disable controller
[12750.305196] nvme 0000:01:00.0: enabling device (0000 -> 0002)
[12750.305465] nvme nvme0: Removing after probe failure status: -19
[12750.313188] nvme nvme0: I/O 456 QID 2 timeout, disable controller
[12750.329152] nvme nvme0: I/O 457 QID 2 timeout, disable controller

The corrected errors are supposedly recovered in hardware without
software intervention, and AER logs them for informational purposes.

But it seems very likely that these corrected errors are related to
the nvme timeout: the first corrected errors were logged at
12720.894411, nvme_io_timeout defaults to 30 seconds, and the nvme
timeout was at 12750.281158.

I don't have any good ideas. As a shot in the dark, you could try
running these commands before doing a suspend:

# setpci -s01:00.0 0x98.W
# setpci -s00:1c.0 0x68.W
# setpci -s01:00.0 0x198.L
# setpci -s00:1c.0 0x208.L

# setpci -s01:00.0 0x198.L=0x00000000
# setpci -s01:00.0 0x98.W=0x0000
# setpci -s00:1c.0 0x208.L=0x00000000
# setpci -s00:1c.0 0x68.W=0x0000

# lspci -vv -s00:1c.0
# lspci -vv -s01:00.0

The idea is to turn off ASPM L1.2 and LTR, just because that's new and
we've had issues with it before. If you try this, please collect the
output of the commands above in addition to the dmesg log, in case my
math is bad.

Bjorn

\
 
 \ /
  Last update: 2018-05-11 18:58    [W:0.035 / U:10.184 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site