lkml.org 
[lkml]   [2018]   [May]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 4/4] dt-bindings: mfd: max8998: Add charger subnode binding
Date
On Tuesday, May 1, 2018 2:45:40 PM CEST Sebastian Reichel wrote:
> Hi,
>
> On Fri, Apr 27, 2018 at 06:03:02PM +0200, Paweł Chmiel wrote:
> > This patch adds devicetree bindings documentation for
> > battery charging controller as the subnode of MAX8998 PMIC.
> > It's based on current behavior of driver.
> >
> > Fixes: ee999fb3f17f ("mfd: max8998: Add support for Device Tree")
> > Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> > ---
> > Documentation/devicetree/bindings/mfd/max8998.txt | 22 ++++++++++++++++++++++
> > 1 file changed, 22 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt
> > index 23a3650ff2a2..f95610afb57f 100644
> > --- a/Documentation/devicetree/bindings/mfd/max8998.txt
> > +++ b/Documentation/devicetree/bindings/mfd/max8998.txt
> > @@ -50,6 +50,21 @@ Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
> > - max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
> > for buck2 regulator that can be selected using dvs gpio.
> >
> > +Charger: Configuration for battery charging controller should be added
> > +inside a child node named 'charger'.
> > + Required properties:
> > + - max8998,charge-eoc: Setup "End of Charge". If value equals 0,
> > + remain value set from bootloader or default value will be used.
> > + Valid values: 0, 10 - 45
> > +
> > + - max8998,charge-restart: Setup "Charge Restart Level". If value equals 0,
> > + remain value set from bootloader or default value will be used.
> > + Valid values: -1, 0, 100, 150, 200
> > +
> > + - max8998,charge-timeout: Setup "Charge Full Timeout". If value equals 0,
> > + remain value set from bootloader or default value will be used.
> > + Valid values: -1, 0, 5, 6, 7
>
> What are those values? seconds?
>
Honestly i don't know. I've just documented values accepted currently by charger driver,
so we can use it from devicetree.
I couldn't find any max8998 datasheet with this information (units, possible values etc for those properties).

If this is not acceptable, i can drop this patch.

> > +
> > Regulators: All the regulators of MAX8998 to be instantiated shall be
> > listed in a child node named 'regulators'. Each regulator is represented
> > by a child node of the 'regulators' node.
> > @@ -99,6 +114,13 @@ Example:
> > max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
> > max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
> >
> > + /* Charger configuration */
> > + charger {
> > + max8998,charge-eoc = <0>;
> > + max8998,charge-restart = <(-1)>;
> > + max8998,charge-timeout = <7>;
> > + };
> > +
> > /* Regulators to instantiate */
> > regulators {
> > ldo2_reg: LDO2 {
>


\
 
 \ /
  Last update: 2018-05-01 16:43    [W:1.351 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site