lkml.org 
[lkml]   [2018]   [Apr]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] wlcore: sdio: allow pm to handle sdio power
Date
pm_runtime handles sdio power on and power off transitions.
An old workaround for trying to control the power explicitly from the
driver was in fact causing failures on suspend/resume as the mmc layer
already power the module on resume.

In case of resume pm_runtime_get sync returns a positive device's usage
count causing the driver to try an re-initialize an already initialized
device. This was causing sdio bus failure on resume.

Remove this manual power on/off sequence as it is in-fact not needed.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
---
drivers/net/wireless/ti/wlcore/sdio.c | 27 ++++++---------------------
1 file changed, 6 insertions(+), 21 deletions(-)

diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
index 1f727ba..6dbe61d 100644
--- a/drivers/net/wireless/ti/wlcore/sdio.c
+++ b/drivers/net/wireless/ti/wlcore/sdio.c
@@ -155,17 +155,11 @@ static int wl12xx_sdio_power_on(struct wl12xx_sdio_glue *glue)
struct mmc_card *card = func->card;

ret = pm_runtime_get_sync(&card->dev);
- if (ret) {
- /*
- * Runtime PM might be temporarily disabled, or the device
- * might have a positive reference counter. Make sure it is
- * really powered on.
- */
- ret = mmc_power_restore_host(card->host);
- if (ret < 0) {
- pm_runtime_put_sync(&card->dev);
- goto out;
- }
+ if (ret < 0) {
+ pm_runtime_put_noidle(&card->dev);
+ dev_err(glue->dev, "%s: failed to get_sync(%d)\n",
+ __func__, ret);
+ goto out;
}

sdio_claim_host(func);
@@ -178,7 +172,6 @@ static int wl12xx_sdio_power_on(struct wl12xx_sdio_glue *glue)

static int wl12xx_sdio_power_off(struct wl12xx_sdio_glue *glue)
{
- int ret;
struct sdio_func *func = dev_to_sdio_func(glue->dev);
struct mmc_card *card = func->card;

@@ -186,16 +179,8 @@ static int wl12xx_sdio_power_off(struct wl12xx_sdio_glue *glue)
sdio_disable_func(func);
sdio_release_host(func);

- /* Power off the card manually in case it wasn't powered off above */
- ret = mmc_power_save_host(card->host);
- if (ret < 0)
- goto out;
-
/* Let runtime PM know the card is powered off */
- pm_runtime_put_sync(&card->dev);
-
-out:
- return ret;
+ return pm_runtime_put_sync(&card->dev);
}

static int wl12xx_sdio_set_power(struct device *child, bool enable)
--
2.7.4
\
 
 \ /
  Last update: 2018-04-26 07:48    [W:0.055 / U:1.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site