lkml.org 
[lkml]   [2018]   [Mar]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 05/11] dt-bindings: i3c: Document core bindings
On Wed, Mar 28, 2018 at 3:19 AM, Boris Brezillon
<boris.brezillon@bootlin.com> wrote:
> Hi Rob,
>
> On Mon, 26 Mar 2018 17:24:58 -0500
> Rob Herring <robh@kernel.org> wrote:
>
>> > +
>> > +I3C devices
>> > +===========
>> > +
>> > +All I3C devices are supposed to support DAA (Dynamic Address Assignment), and
>> > +are thus discoverable. So, by default, I3C devices do not have to be described
>> > +in the device tree.
>> > +This being said, one might want to attach extra resources to these devices,
>> > +and those resources may have to be described in the device tree, which in turn
>> > +means we have to describe I3C devices.
>> > +
>> > +Another use case for describing an I3C device in the device tree is when this
>> > +I3C device has a static address and we want to assign it a specific dynamic
>> > +address before the DAA takes place (so that other devices on the bus can't
>>
>> static is I2C address and dynamic is an I3C address. That could be
>> clearer throughout.
>
> I'll clarify that.
>
>>
>> > +take this dynamic address).
>> > +
>> > +The I3C device should be names <device-type>@<static-address>,<i3c-pid>,
>>
>> s/static-address/static-i2c-address/
>
> Okay.
>
>>
>> > +where device-type is describing the type of device connected on the bus
>> > +(gpio-controller, sensor, ...).
>> > +
>> > +Required properties
>> > +-------------------
>> > +- reg: contains 3 cells
>> > + + first cell : encodes the I2C address. Should be 0 if the device does not
>> > + have one (0 is not a valid I3C address).
>>
>> Change here to "encodes the static I2C address".
>>
>> 0 is not a valid I2C address?
>
> According to [1] it is reserved, and it's reserved in the I3C spec
> anyway (see "Table 9 I3C Slave Address Restrictions" in the I3C spec).

Sorry, what I meant was s/I3C/I2C/. The first cell is I2C address and
0 is not valid.

>> > +
>> > + + second and third cells: should encode the ProvisionalID. The second cell
>> > + contains the manufacturer ID left-shifted by 1.
>> > + The third cell contains ORing of the part ID
>> > + left-shifted by 16, the instance ID left-shifted
>> > + by 12 and the extra information. This encoding is
>> > + following the PID definition provided by the I3C
>> > + specification.
>
> One extra question for you: should I refer to the I3C_DEV(),
> I3C_DEV_WITH_STATIC_ADDR() and I2C_DEV() macros in the bindings doc?
> And if I do, should I use them my example?

Well, I don't want to see "device@I3C_DEV(...)" for unit-addresses.
You can use them for reg property, but it's somewhat pointless to use
it in one place and not the other.

Rob

\
 
 \ /
  Last update: 2018-03-28 18:42    [W:0.121 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site