lkml.org 
[lkml]   [2018]   [Mar]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v1 1/2] dt-bindings: usb: Update documentation for Qualcomm DWC3 driver
From
Date
Hi,


On 3/18/2018 6:19 PM, Rob Herring wrote:
> On Tue, Mar 13, 2018 at 04:06:00PM +0530, Manu Gautam wrote:
>> Existing documentation has lot of incorrect information as it
>> was originally added for a driver that no longer exists.
>>
>> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
>> ---
>> .../devicetree/bindings/usb/qcom,dwc3.txt | 87 +++++++++++++++-------
>> 1 file changed, 59 insertions(+), 28 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
>> index bc8a2fa..df312f7 100644
>> --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
>> +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
>> @@ -1,54 +1,85 @@
>> Qualcomm SuperSpeed DWC3 USB SoC controller
>>
>> Required properties:
>> -- compatible: should contain "qcom,dwc3"
>> -- clocks: A list of phandle + clock-specifier pairs for the
>> - clocks listed in clock-names
>> -- clock-names: Should contain the following:
>> - "core" Master/Core clock, have to be >= 125 MHz for SS
>> - operation and >= 60MHz for HS operation
>> -
>> -Optional clocks:
>> - "iface" System bus AXI clock. Not present on all platforms
>> - "sleep" Sleep clock, used when USB3 core goes into low
>> - power mode (U3).
>> +- compatible: should contain "qcom,dwc3"
>> +- reg: offset and length of register set for QSCRATCH wrapper
>> +- reg-names: should be "qscratch"
> reg-names is pointless for a single range.
Ok. Will change this.

>
>> +- power-domains: specifies a phandle to PM domain provider node
>> +- clocks: list of phandle + clock-specifier pairs
> How many clocks and what are they?
I will add description of the clocks in next version of patchset.


>
>> +- assigned-clocks: should be:
>> + MOCK_UTMI_CLK
>> + MASTER_CLK
>> +- assigned-clock-rates: should be:
>> + 19.2Mhz (192000000) for MOCK_UTMI_CLK
>> + >=125Mhz (125000000) for MASTER_CLK in SS mode
>> + >=60Mhz (60000000) for MASTER_CLK in HS mode
>> +
>> +Optional properties:
>> +- resets: list of phandle and reset specifier pairs
>> +- interrupts: specifies interrupts from controller wrapper used
>> + to wakeup from low power/susepnd state. Must contain
>> + one or more entry for interrupt-names property
>> +- interrupt-names: Must include the following entries:
>> + - "hs_phy_irq": The interrupt that is asserted when a
>> + wakeup event is received on USB2 bus
>> + - "ss_phy_irq": The interrupt that is asserted when a
>> + wakeup event is received on USB3 bus
>> + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate
>> + interrupts for any wakeup event on DM and DP lines
>> +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement.
>> + Used when dwc3 operates without SSPHY and only
>> + HS/FS/LS modes are supported.
>>
>> Required child node:
>> A child node must exist to represent the core DWC3 IP block. The name of
>> the node is not important. The content of the node is defined in dwc3.txt.
>>
>> Phy documentation is provided in the following places:
>> -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
>> +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY
>> +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY

--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

\
 
 \ /
  Last update: 2018-03-19 05:21    [W:0.154 / U:0.600 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site